Analysis of hypothetical deboration transients

This work was carried out in the frame of the project "Development of methods for the analysis of accident scenarios with steam line breaks and boron dilution by the help of the code system ATHLET-DYN3D" (registration number: 1501225) funded from 01.07.2000 to 31.03.2004 by the German Federal Ministry of Economics and Labour.

Background

The underlying scenario is based on an unrecognised steam generator tube rupture. It is assumed, that a slug of unborated coolant has accumulated in the loop during outage, when the secondary side pressure was higher than that in the primary side. It is assumed further, that this deborated coolant is driven by switching-on the main coolant pump in the affected loop to the reactor pressure vessel and core inlet.
This hypothetical scenario was investigated in the frame of a parameter study with the following steps:
1. Calculation of the transient course of the boron concentration at the inlet into each fuel assembly for each initial slug volume between 0 and the bounding one of 36 m3 by the help of the semi-analytical mixing model SAPR (the stepwidth of the increasing is 4 m3).
2. Extraction of the core inlet distribution of the boron concentration at the time point of minimum.
3. Stationary core calculations by means of DYN3D
3.1 with the assumption, that the minimum value of the boron concentration is present in the whole reactor.
3.2 using the calculated core inlet distribution, but extending it over the whole height of the reactor.
4. Transient core calculations for the initial slug volumes, for which the stationary calculations showed a over-criticality (using the calculated by SAPR time-dependent boron concentration at the inlet into each fuel assembly).

Stationary core calculations

For the calculations, a generic equilibrium core-loading pattern of a pressurized water reactor containing 64 MOX fuel elements was used. The corresponding scheme is shown on Fig. 1. It is assumed, that the most effective control stays at fully withdrawn position.
Fig. 2 shows the distribution of the boron concentration at the core inlet calculated by SAPR at the time point of minimum. As initial condition, the boron concentration in the lower plenum of the reactor was set to 2200 ppm and in the slug to 0 ppm.
These distributions were used as boundary conditions for the stationary core calculations (extended over the whole height of the reactor).

The calculated Keff-values for the reactor core are shown on Fig. 3. The use of the minimum boron concentration in the whole reactor leads of course to considerable higher Keff-values. From the calculations it follows, that under these conditions a recriticality of the core can be expected already for initial slug volumes between 8 and 12 m3, while for the conditions of a realistic distribution at the core inlet only between 12 and 16 m3.


Fig. 1: Loading pattern of the generic reactor core used in the calculations

Fig. 2: Distribution of the boron concentration at the time point of minimum in dependance on the initial slug volume in the cold leg (calculated by SAPR)





Fig. 3: Dependance of the stationary reactivity on the initial slug volume


Transient core calculations

The stationary calculations showed, that only slug volumes greater than 12 m3 can lead to a recriticality of the switched-off reactor. Therefore, the first transient calculation was carried out for the initial slug volume of 16 m3.
In this case, the average boron concentration in the reactor core (Fig. 4) reaches only a minimum value of 1503 ppm about 20 s after switching-on the main coolant pump. The dynamic reactivity (Fig. 5) remains below the zero-line throughout the whole transient. The reactor becomes not critical, what is contrary to the stationary calculations presented above . That can be explained by the fact, that the slug has a finite length, what could not be taken into consideration in the stationary calculations, where the inlet distribution was extended over the whole height.
With an initial slug volume of 20 m3, the average boron concentration in the reactor core decrease to a value of less than 1400 ppm. This leads to a positive insertion of reactivity into the core, which not only compensates the intial sub-criticality, but leads also to a significant over-criticality of about 2 $. A corresponding power peak of about 1.7 times the nominal power (Fig. 6) is reached. Due to the prompt acting Doppler feedback, the further power increase is stopped, the half width of the peak is 23 ms. The insertion of energy into the fuel and the coolant during the peak is low, boiling did not occur. The compensation of the initial sub-criticality happens at about the time of the minimum of the boron content in the core. The following after the slug higher borated coolant transfers the reactor to a sub-critical state, again. The transient is finished.


Fig. 4: Time history of the average boron concentration in the reactor core for initial slug volumes of 16, 20 and 36 m3


Fig. 5: Time history of the reactivity for initial slug volumes of 16, 20 and 36 m3





The average boron concentration in the reactor core decreases to a significantly lower value in the calculation with the bounding slug volume of 36 m3. The positive reactivity insertion leads earlier to a compensation of the initial sub-criticality, the dynamic reactivity reaches the zero-line already at t= 16.5s. The reached maximum value is with slightly more than 2 $ in the same order as for the previous calculation. The Doppler feedback stops the power increase at a value of 2.3 in comparison to the nominal value, the half width is 21 ms. Contrary to the slug of 20 m3, the reactor becomes critical before the boron content in the core reaches the minimum. Because the positive reactivity insertion is continued after the power peak appears, typical secondary power peaks emerge. The interaction of the continuing deboration with negative Doppler and moderator feedback effects determine the height and frequency of these power peaks. The total reactivity remains below the super-prompt margin, which is the reason that these power peaks do not reach the height of the first one.

As can be seen from Fig. 7, the radial power distribution over the reactor core is very heterogeneous. This is caused by the superposition of the deboration with the stuck control rod. The moving of the deboration front through the reactor core is demonstrated in the animation in Fig. 8. There, the isosurface of 800 ppm is shown. It is clearly to be seen, that the front enters the core at two positions, what causes a local deboration. This deboration front moves into the core, while on the opposite side, the boron concentration does not decrease below a value of 800 ppm. Further, it is clearly to be seen, that the deborated volume never fills the whole height of the reactor. The leading front of the lower borated slug has not reached the upper end of the core, when from the core inlet already highly borated coolant is supplied.


Fig. 7: Power distribution at time point of maximum (slug volume of 36 m3)
 
Fig. 6: Time history of the core power for the slug volumes of 20 und 36 m3


Fig. 8: Transport of the deboration front through the core on the example of the Isosurface of 800 ppm (slug volume of 36 m3)



Fig. 9: Development and transport of void in the core on the example of the Isosurface of 10 % void fraction (slug volume of 36 m3)


During the secondary power peaks, coolant boiling starts in single fuel elements, a maximum value of more than 70 % is reached. The animation in Fig. 9 demonstrates, again on behalf of an isosurface, how void appears in the upper part of single fuel elements and how the void is transported to the outlet of the core. This animation underlines the heterogeneous character of the transient, again. The critical heat flux density is not reached in these channels, the maximum inserted enthalpy does not reach any critical boundary value, too.

Publications

Contact

S. Kliem