Publications Repository - Helmholtz-Zentrum Dresden-Rossendorf

"Online First" included
Approved and published publications
Only approved publications

41396 Publications

Donor-Acceptor Conjugated Acetylenic Polymers for Co- Catalysts-Free Overall Photoelectrochemical Water Splitting

Borrelli, M.; An, Y.; Joy Querebillo, C.; Morag, A.; Neumann, C.; Turchanin, A.; Sun, H.; Kuc, A. B.; Weidinger, I. M.; Feng, X.

Due to the drastic required thermodynamical requirements, a photoelectrode material that can function as both a photocathode and a photoanode remains elusive. In this work, we demonstrate for the first time that, under simulated solar light and without co-catalysts, donor- acceptor conjugated acetylenic polymers (CAPs) exhibit both impressive oxygen evolution (OER) and hydrogen evolution (HER) photocurrents in alkaline and neutral medium, respectively. In particular, poly(2,4,6-tris(4-ethynylphenyl)-1,3,5-triazine) (pTET) provides a benchmark OER photocurrent density of ~200 μA cm-2 at 1.23 V vs. reversible hydrogen electrode (RHE) at pH 13 and a remarkable HER photocurrent density of ~190 μA cm-2 at 0.3 V vs. RHE at pH 6.8. By combining theoretical investigations and electrochemical-operando Resonance Raman spectroscopy, we show that the OER proceeds with two different mechanisms, with the electron-depleted triple bonds acting as single-site OER in combination with the C4-C5 atoms of the phenyl rings as dual sites. The HER, instead, occurs via an electron transfer from the tri-acetylenic linkages to the triazine rings, which act as the HER active sites. This work represents a novel application of organic-based materials and contributes to the development of high-performance photoelectrochemical catalysts for the solar fuels’ generation.

Permalink: https://www.hzdr.de/publications/Publ-36960
Publ.-Id: 36960


Understanding hydrogen diffusion in between layers of 2D materials

Eren, I.; Yun, A.; Kuc, A. B.

In 2018, the group of Geim from Manchester performed very interesting experiments, in which hydrogen atoms were diffused and transported inside the interstitial space of layered materials, such as hexagonal boron nitride or MoS2, showing a good sieving of deuterium from protium. We later showed theoretically that indeed hydrogen atoms rather than ions are transported between the layers and reported their diffusion coefficients. We also showed that the transport is assisted by the layer shearing mode. In this work, we investigated the hydrogen diffusion between layers of different transition-metal dichalcogenides (TMDCs), where we studied the influence of possible stackings, stoichiometry, and exemplary twist angles between layers on the self-diffusion coefficient. The calculations were performed using well-tempered metadynamics simulations as implemented in CP2K package, which gives us access to the free energy surface. We found that TMDCs with Se or Mo atoms have lower free energy barriers than these with S or W. Furthermore, structural stackings of MoS2 (𝐻ℎℎ(2H), 𝑅ℎ𝑋 (3R), 𝑅ℎℎ, 𝐻ℎ𝑀, 𝐻ℎ𝑋) also result in different free energy barriers. These energy barriers affect strongly the self-diffusion coefficients, because they enter the diffusion equation as exponent.

  • Poster
    Symposium on Theoretical Chemistry 2022, 15.-18.09.2022, Heidelberg, Germany
  • Poster
    Chem2dmat, 15.-18.05.2023, Bologna, Italy
  • Poster (Online presentation)
    20 years of metadynamics, 05.-08.09.2022, Lausanne, Switzerland
  • Poster
    PISACMS 2022: Paris International School on Advanced Computational Materials Science, 28.08.-01.09.2022, Paris, France

Permalink: https://www.hzdr.de/publications/Publ-36959
Publ.-Id: 36959


Preclinical trial comparing radiotherapy alone versus standard radiochemotherapy in three human papilloma virus (HPV) negative and three HPV-positive head and neck squamous cell carcinoma (HNSCC) xenograft tumour models.

Valentini, C.; Ebert, N.; Koi, L.; Pfeifer, M.; Löck, S.; Erdmann, C.; Krause, M.; Baumann, M.

Purpose: To perform a preclinical trial comparing the efficacy of fractionated radiotherapy versus
radiochemotherapy with cisplatinum in HPV-positive and negative human head and neck
squamous cell carcinoma (HNSCC) xenografts.
Material and methods: Three HPV-negative and three HPV-positive HNSCC xenografts in nude
mice were randomized to radiotherapy (RT) alone or to radiochemotherapy (RCT) with weekly
cisplatinum. To evaluate tumour growth time, 20 Gy radiotherapy (± Cisplatin) were administered
in 10 fractions over 2 weeks. Dose-response curves for local tumor control were generated for RT
with 30 fractions over 6 weeks to different dose levels given alone or combined with cisplatinum
(RCT).
Results: One of three investigated HPV-negative and two out of three HPV-positive tumour
models showed a significant increase in local tumour control after RCT compared to RT alone.
Pooled analysis of HPV-positive tumour models showed a statistically significant and substantial
benefit of RCT versus RT alone, with an enhancement ratio of 1.34. Although heterogeneity in
response to both RT and RCT was also observed between the different HPV-positive HNSCC,
these overall were more RT and RCT sensitive than HPV-negative models.
Conclusion: The impact of adding chemotherapy to fractionated radiotherapy on local control was
heterogenous, both in HPV-negative and in HPV-positive tumours, calling for predictive
biomarkers. RCT substantially increased local tumour control in the pooled group of all HPVpositive
tumours whereas this was not found in HPV-negative tumours. Omission of chemotherapy
in HPV-positive HNSCC as part of a treatment de-escalation strategy is not supported by this
preclinical trial.

Keywords: HPV; HNSCC; Radiotherapy; Radiochemotherapy; Tumour models

Permalink: https://www.hzdr.de/publications/Publ-36957
Publ.-Id: 36957


Polymorph Conversion in Gallium Oxide via Focused Ion Beam

Bektas, U.; Klingner, N.; Chekhonin, P.; Liedke, M. O.; Hübner, R.; Heller, R.; Ganss, F.; Hlawacek, G.

Monoclinic gallium oxide (β-Ga2O3) is the chemically and thermally most stable compound, compared to its other four polymorphs, with an ultra-wide bandgap of 4.9 eV. It is a promising semiconductor material for power electronics, optoelectronics, and batteries. However, controlling the metastable polymorph phases is quite hard, and the fabrication technology at the nanoscale is immature. Our goal is to understand and utilize ion beam-induced polymorph conversion. Controlling the crystalline structure will allow us to establish new fabrication methods of single-phase polymorph layers, buried layers, multilayers, and different nanostructures in Ga2O3 using focused ion beams (FIBs). The research aims to better understand and control the polymorph conversion, emphasizing spatially resolved modifications by utilizing focused ion beams.
Most of the semiconductor materials transform into an amorphous phase under a high dose of ion irradiation, however, gallium oxide is an exceptionally radiation-tolerant material even at high fluences. In a previous study, Kuznetsov et.al. [1] demonstrated the ion-beam-induced β-to-κ phase trans-formation in Ga2O3 as shown in Fig.1. However, later, Garcia Fernandez et.al. [2] showed that the monoclinic β-phase actually transforms into the cubic γ-phase. Additional experimental and simulation results suggest that the formed gamma layer is not only stable up to several hundred degrees but also can tolerate high fluencies of additional ion irradiation. The conversion from the stable to the meta-stable phase seems to be enabled by the formation of a defective spinel structure in which the oxygen lattice remains unchanged [3].
Here, we used Helium Ion Microscopy (HIM) and liquid metal alloy ion source (LMAIS) FIBs to locally irradiate the (-201) oriented β-Ga2O3 sample with different ions (Ne, Ga, Co, Nd, Si, Au, In) to induce the polymorph transition. The successful conversion into γ- Ga2O3 under Ne+ irradiation (Fig.2(a)) has been confirmed by using Electron Backscattered Diffraction (EBSD) and indexing the Kikuchi patterns (Fig.2(b)). Furthermore, Doppler broadening variable energy positron annihilation spectroscopy (DB-VEPAS) and Rutherford Backscatter Spectrometry (RBS) were performed for neon broad beam irradiated implants to better understand the fluence-dependent creation and distribution of defects. Transmission Electron Microscopy (TEM) images also provide information about the distinct and sharp interfaces between different polymorphs of Ga2O3. The first results indicate that the damage/strain created by the Ne+, Co+, and Si+ FIB irradiation leads to a local transformation of β- Ga2O3 to γ- Ga2O3 and the structure maintains its crystallinity even under the high fluence of ion irradiation instead of being amorphized.

Keywords: Gallium Oxide; Helium Ion Microscopy; Focused Ion Beam; Positron Annihilation Lifetime Spectroscopy; Polymorph Transition; Transmission Electron Microscopy; Electron Backscatter Diffraction; Rutherford backscatter spectroscopy

Related publications

  • Open Access Logo Lecture (Conference)
    3rd FIT4NANO, 15.-19.07.2023, Lisbon, Portugal

Permalink: https://www.hzdr.de/publications/Publ-36956
Publ.-Id: 36956


How to grow single-crystalline and epitaxial NiTi films in (100)- and (111)-orientation

Lünser, K.; Undisz, A.; Nielsch, K.; Fähler, S.

Understanding the martensitic microstructure in NiTi thin films helps to optimize their properties for applications in microsystems. Epitaxial and single-crystalline films can serve as model systems to understand the microstructure, as well as to exploit the anisotropic mechanical properties of NiTi. Here, we analyze the growth of NiTi on single-crystalline MgO(100) and Al2O3(0001) substrates and optimize film and buffer deposition conditions to achieve epitaxial films in (100)- and (111)-orientation. On MgO(100), we compare the transformation behavior and crystal quality of (100)-oriented NiTi films on different buffer layers. We demonstrate that a vanadium buffer layer helps to decrease the low-angle grain boundary density in the NiTi film, which inhibits undesired growth twins and leads to higher transformation temperatures. On Al2O3(0001), we analyze the orientation of a chromium buffer layer and find that it grows (111)-oriented only in a narrow temperature range around 500 °C. By depositing the Cr buffer below the NiTi film, we can prepare (111)-oriented, epitaxial films with transformation temperatures above room temperature. Transmission electron microscopy (TEM) confirms a martensitic microstructure with Guinier Preston (GP)-zone precipitates at room temperature. We identify the deposition conditions to approach the ideal single crystalline state, which is beneficial for the analysis of the martensitic microstructure and anisotropic mechanical properties in different film orientations.

Keywords: NiTi films; shape memory alloys; epitaxial film growth; Nitinol

Related publications

Permalink: https://www.hzdr.de/publications/Publ-36955
Publ.-Id: 36955


Europium(III) Meets Etidronic Acid (HEDP): a Coordination Study Combining Spectroscopic, Spectrometric, and Quantum Chemical Methods

Heller, A.; Senwitz, C.; Foerstendorf, H.; Tsushima, S.; Holtmann, L.; Drobot, B.; Kretzschmar, J.

Etidronic acid (HEDP, H4L) is a proposed decorporation agent for U(VI). In this paper, we studied its complex formation with Eu(III), an inactive analog of trivalent actinides, over a wide pH range, at varying metal to ligand ratios (M:L) and total concentrations. Combining spectroscopic, spectrometric, and quantum chemical methods, five distinct Eu(III)−HEDP complexes were found, four of which were characterized. At acidic pH, the readily soluble EuH2L+ and Eu(H2L)2− species with log β values of 23.7 ± 0.1 and 45.1 ± 0.9 are formed. At near-neutral pH, EuHL0s forms with a log β of ~23.6 and, additionally, a most probably polynuclear complex. At alkaline pH, the readily dissolved EuL− species with a log ß of ~11.2 is formed. A six-membered chelate ring is the key motif in all solution structures. The equilibrium between the Eu(III)–HEDP species is influenced by several parameters, i.e. pH, M:L, total Eu(III) and HEDP concentrations, and time. Overall, the present work sheds light on the very complex speciation in the HEDP–Eu(III) system and indicates that, for risk assessment of potential decorporation scenarios, side reactions of HEDP with trivalent actinides and lanthanides should also to be taken into account.

Permalink: https://www.hzdr.de/publications/Publ-36954
Publ.-Id: 36954


Efficient calculations of electronic structures with machine-learning models

Fiedler, L.

Quantum mechanical calculations of the electronic structure of matter enable accessing interesting thermodynamical properties without the need for prior experimental measurements.
Therefore, electronic structure calculations are of great interest in fields such as materials discovery or drug design. At the forefront of such simulations lies density functional theory (DFT), due to its excellent balance between computational accuracy and efficiency. Yet, as pressing environmental and social issues shift the research focus to increasingly complicated systems and conditions, even the most efficient of DFT implementations are approaching their limitations in terms of computational feasibility. A possible route to enable more complex calculations lies with machine learning (ML), i.e., algorithms that are capable of capturing complicated relationships based on large amounts of data.

Keywords: Density Functional Theory; Machine Learning

  • Open Access Logo Lecture (others)
    CASUS institute seminar, 02.05.2023, Görlitz, Deutschland
  • Open Access Logo Invited lecture (Conferences) (Online presentation)
    SciML Webinar Series, 09.11.2023, University of Michigan, USA

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36953
Publ.-Id: 36953


Eulerian simulation of co-current solid-liquid flow in a vertical pipe

Draw, M.; Rzehak, R.

The prediction of solid-liquid flow in a pipe is of significance for a variety of industrial processes. Since the physical phenomena in such processes appear on widely differing length- and time-scales, many CFD methods are not quite cost-effective. The Euler-Euler multiphase approach makes it feasible to simulate such flows with reasonable computation time. The main challenge of this approach lies in the modeling of the interfacial momentum exchange between the phases, since the interface is not resolved. In this paper, a baseline model is validated that describes the interfacial forces (drag, virtual mass, (shear-) lift, wall (-lift), and turbulent dispersion) between solid particles and a liquid. This model is validated against experimental data of positively and negatively buoyant particles in a vertical pipe flow from the literature. The results show a reasonable agreement with the experimental data, except for the solid volume fraction distribution in the negatively buoyant particle cases. Possible reasons for this are discussed.

Keywords: solid-liquid two-phase flow; Euler-Euler two-fluid model; closure models; vertical pipe flow

  • Lecture (Conference)
    The 11th International Conference on Multiphase Flow, 02.-07.04.2023, Kobe, Japan

Permalink: https://www.hzdr.de/publications/Publ-36952
Publ.-Id: 36952


Federated Deep Learning With Prototype Matching for Object Extraction From Very-High-Resolution Remote Sensing Images

Zhang, X.; Zhang, B.; Yu, W.; Kang, X.

Deep convolutional neural networks (DCNNs) have become the leading tools for object extraction from very-high-resolution (VHR) remote sensing images. However, the label scarcity problem of local datasets hinders the prediction performances of DCNNs, and privacy concerns regarding remote sensing data often arise in the traditional deep learning schemes. To cope with these problems, we propose a novel federated learning scheme with prototype matching (FedPM) to collaboratively learn a richer DCNN model by leveraging remote sensing data distributed among multiple clients. This scheme conducts the federated optimization of DCNNs by aggregating clients’ knowledge in the gradient space without compromising data privacy. Specifically, the prototype matching method is developed to regularize the local training using prototypical representations while reducing the distribution divergence across heterogeneous image data. Furthermore, the derived deviations across local and global prototypes are applied to quantify the effects of local models on the decision boundary and optimize the global model updating via the attention-weighted aggregation scheme. Finally, the sparse ternary compression (STC) method is used to alleviate communication costs. Extensive experimental results derived from VHR aerial and satellite image datasets verify that the FedPM can dramatically improve the prediction performance of DCNNs on object extraction with lower communication costs. To the best of our knowledge, this is the first time that federated learning has been applied for remote sensing visual tasks.

Keywords: Deep Learning; Federated Learning; Object Extraction; Remote Sensing Images; Semantic Segmentation

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36951
Publ.-Id: 36951


Data publication: Gallium bioionflotation using rhamnolipid: Influence of frother addition and foam properties

Chakankar, M. V.; Oestreich, A.; Pollmann, K.; Rudolph, M.

The current study investigated the application of rhamnolipid biosurfactant as an ion collector in bioionflotation. In a top-down approach, the influence of rhamnolipid on gallium (Ga) ion flotation and recovery were investigated followed by detailed studies on the influencing parameters and foam characterization. Rhamnolipid exhibits extensive foaming properties and foam produced by rhamnolipid alone has higher stability making it difficult to collect the flotation concentrates. An addition of 1,2-decanediol introduces instability to this foam and also aids in concentrate collection. Observations during the flotation studies resulted in a series of investigations on rhamnolipid properties such as aggregate size, surface tension, and foam characterization. These results indicated that the addition of Ga and/or 1,2-decanediol affected the molecular aggregation of rhamnolipid. Moreover, the surface activity, foamability, foam drainage, and foam coarsening/coalescence of the rhamnolipid changed in the presence of Ga and/or 1,2-decanediol. In a batch bioionflotation process, rhamnolipid was able to remove nearly 80% Ga at pH 7 in presence of 1,2-decanediol. However, upgrading was higher at pH 6 without 1,2-decanediol, which is important when considering the flotation recovery in presence of other metals. Such biosurfactants have a high potential for wide applications in ion flotation and further optimization of flotation parameters is essential.

Keywords: Rhamnolipid; biosurfactant; ion flotation; Foam characterization; Gallium; surface tension

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36950
Publ.-Id: 36950


Microbial Influence on Cast Iron Corrosion-Approach of the UMB-II project

Matschiavelli, N.

Talk about the recent results within the UMB-II Project. Main focus here is the influence of intrinsic microbial bentonite communities on the corrosion of cast iron.

  • Lecture (others)
    FWOB-Seminar, 25.05.2023, Helmholtz-Zentrum Dresden-Rossendorf, Deutschland

Permalink: https://www.hzdr.de/publications/Publ-36948
Publ.-Id: 36948


Further development, validation and verification of the Monte-Carlo code TRAMO on ex-vessel experiments of the Greifswald NPP

Baier, S.; Konheiser, J.; Pönitz, E.

TRAMO is a Monte Carlo code which is specially designed for geometries of nuclear power plants. In recent years, TRAMO has undergone a number of technical developments. In addition to the conversion to modern Fortran, standardized models for VVER-440 and VVER-1000 for the evaluation of monitor experiments on the surface of the reactor pressure vessel were developed, and the corresponding pre- and post-processing was automated. The new TRAMO version is continuously validated and verified. Here we present comparisons with experimental data from unit 1 of the Greifswald nuclear power plant and with MCNP calculations. Earlier calculations with TRAMO showed good agreements in the middle region of the fission zone, but significant deviations outside. A possible explanation is the wrong documentation of the experimental data – especially the heights of the monitors. Assuming a downward shift of the monitor positions by about 24cm, experimental and calculated data show very good agreement.

Keywords: reactor dosimetry; neutron fluence calculation; activity measurements; Monte Carlo code; Monte Carlo calculation

  • Poster
    17th International Symposium on Reactor Dosimetry, 21.-26.05.2023, Lausanne, Schweiz

Permalink: https://www.hzdr.de/publications/Publ-36947
Publ.-Id: 36947


Data for "How to grow single-crystalline and epitaxial NiTi films in (100)- and (111)-orientation"

Lünser, K.; Undisz, A.; Nielsch, K.; Fähler, S.

This dataset belongs to the paper "How to grow single-crystalline and epitaxial NiTi films in (100)- and (111)-orientation" and contains all raw data used for the paper. It includes AFM, SEM, R(T), TEM, Texture measurements and rocking curves.  Information about samples, measurement techniques and file naming conventions can be found in README.txt. 

Keywords: NiTi films; shape memory alloys; epitaxial film growth; Nitinol

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36945
Publ.-Id: 36945


surface pressure isotherms for punicine derivatives and oleic acid/sodium oleate

Pfeufer, R. A.

Data sets of surface pressure isotherms for punicine derivatives (octyl-, nonyl-, decyl-, undecyl- and heptadecyl-punicine) and oleic acid/sodium oleate.

Measurements were carried out at the Langmuir-Blodgett Minitrough of KSV Instruments Ltd. For each measurement the surfactant was solubilized in 1:1 EtOH and chloroform. This solution was placed on top of water (conductivity < 0.8 µS) and after an evaporation time of 10 min measurements were started.

Keywords: Langmuir-Blodgett trough; punicine; surface pressure isotherm

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36944
Publ.-Id: 36944


dynamic contact angles of water of uncoated and coated (heptadecyl punicine) on quartz, hiddenite and kunzite

Pfeufer, R. A.

data sets of dynamic contact angle measurements of water onuncoated and coated (heptadecyl punicine) hiddenite, kunzite and quartz.

Measurements were carried out at the OCA25 from DataPhysics Instruments GmbH with the ARCA method.

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36943
Publ.-Id: 36943


Pendant drop mesurements for water and decyl punicine in water

Pfeufer, R. A.

data sets of pendant drop measurements of aqueous decyl punicine solution.

Measurements were carried out at the OCA25 from DataPhysics Instruments GmbH .

Keywords: punicine; pendant drop; interfacial tension

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36942
Publ.-Id: 36942


bubble pressure tensiometry for punicine derivatives and oleic acid/sodium oleate

Pfeufer, R. A.

Data sets of surface tension of puncine derivatives (octyl-, nonyl-, decyl-, undecyl- and heptadecyl-punicine) and oleic acid/sodium oleate in water measured with bubble pressure tensiometry at different pH and different concentrations.

Measurements were done at BP100 of KRÜSS GmbH. For each mesurement the adequate amount of a 25mM surfactant solution (40 vol-% EtOH and 60vol-% distilled water) werde diluted in 70 mL of distilled water.

Keywords: bubble pressure; punicine; surface tension

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36941
Publ.-Id: 36941


zetapotential of spodumene with decyl punicine

Pfeufer, R. A.

Data set of zetapotential measurements of a spodumene dispersion and spodumene dispersion with decyl punicine.

Measurements were carried out in 10 mM KCl background at 2.5 wt-% spodumene (x < 10 µm). For the measurement with decyl punicine a concentration of 10 µM surfactant was used.

Keywords: Zetapotential; punicine; spodumene

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36940
Publ.-Id: 36940


Effect of physical exercise on brain perfusion in chemotherapy-treated breast cancer patients: a randomized controlled trial (PAM study)

Koevoets, E. W.; Petr, J.; Monninkhof, E. M.; Geerlings, M. I.; Witlox, L.; van der Wall, E.; Stuiver, M. M.; Sonke, G. S.; Velthuis, M. J.; Jobsen, J. J.; van der Palen, J.; Jmm Mutsaerts, H.; de Ruiter, M. B.; May, A. M.; Schagen, S. B.

BACKGROUND Breast cancer patients may experience cognitive difficulties after chemotherapy.
PURPOSE To investigate whether an exercise intervention can affect cerebral blood flow (CBF) in breast cancer patients and if CBF changes relate to memory function.
STUDY TYPE Prospective.
POPULATION Chemotherapy-treated breast cancer patients with cognitive problems, and with relatively low physical activity levels were randomized to an exercise intervention (n=91) or control group (n=90).
FIELDSTRENGTH/SEQUENCE A 3-T arterial spin labeling CBF scan was performed.
ASSESSMENT The 6-month intervention consisted of (supervised) aerobic and strength training, 4x1 hour/week. Measurements at baseline (2-4 years post-diagnosis) and after six months included the arterial spin labeling CBF scan, from which we calculated gray matter CBF in the whole brain, hippocampus, anterior cingulate cortex, and posterior cingulate cortex. Furthermore, we measured physical fitness and memory functioning.
STATISTICAL TESTS Multiple regression analyses with a two-sided alpha of 0.05 for all analyses.
RESULTS We observed significant improvement in physical fitness (VO2peak) in the intervention group (n=53) compared to controls (n=51, B1.47, 95%CI:0.44; 2.50), nevertheless no intervention effects on CBF were found (e.g. whole brain: B0.98, 95%CI:-2.38; 4.34). Highly fatigued patients showed larger, but not significant, treatment effects. Additionally, change in physical fitness, from baseline to post-intervention, was positively associated with changes in CBF (e.g., whole brain: B0.75, 95%CI:0.07; 1.43). However, we observed no relation between CBF changes and change in memory performance.
DATA CONCLUSION The exercise intervention did not affect CBF of cognitively affected breast cancer patients. However, a change in physical fitness was related to a change in CBF, but a change in CBF was not associated with memory functioning.

  • Open Access Logo Journal of Magnetic Resonance Imaging (2024)
    Online First (2023) DOI: 10.1002/jmri.28967

Permalink: https://www.hzdr.de/publications/Publ-36939
Publ.-Id: 36939


Brain tumor imaging without gadolinium-based contrast agents: Feasible or Fantasy?

Wamelink, I. J. H. G.; Azizova, A.; Booth, T. C.; Mutsaerts, H. J. M. M.; Ogunleye, A.; Mankad, K.; Petr, J.; Barkhof, F.; Keil, V. C.

Gadolinium-based contrast agents (GBCA) form the cornerstone of current primary brain tumor MRI protocols at all stages of the patient journey. Though an imperfect of tumor grade, GBCA is repeatedly used for diagnosis and monitoring.
In practice, however, radiologists will encounter situations where GBCA injection is unwanted or of doubtful benefit. Reducing GBCA administration could improve the patient burden of (repeated) imaging, especially in vulnerable patient groups such as children, minimize risks of putative side effects, as well as benefit costs, logistics, and the environmental footprint.
This review presents standard imaging strategies to reduce GBCA exposure for pediatric and adult patients with primary brain tumors, including the effect of prolonging follow-up intervals and omitting contrast-enhanced sequences. The potential of novel pulse sequences, such as arterial spin labeling, and upcoming artificial intelligence methods, e.g., to generate synthetic post-contrast images, promise to replace GBCA-dependent approaches. To attain a concise summary of the knowledge in the field, gliomas and meningiomas as typical representatives of primary brain tumors are the review’s focus. Special attention is paid to study quality and real-life applicability.

Permalink: https://www.hzdr.de/publications/Publ-36938
Publ.-Id: 36938


Data publication: Integration of Multifunctional Epitaxial (Magnetic) Shape Memory Films in Silicon Microtechnology

Fink, L.; Kar, S.; Lünser, K.; Nielsch, K.; Reith, H.; Fähler, S.

Measured raw data (XRD, texture, SEM, PPMS and EDX)

Keywords: Magnetic shape memory alloys; Silicon microtechnology; Ni2MnGa; NiTi; Epitaxial film growth

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36937
Publ.-Id: 36937


Millisecond Flash Lamp Curing for Porosity Generation in Thin Films

Attallah, A. G.; Prucnal, S.; Butterling, M.; Hirschmann, E.; Koehler, N.; Schulz, S. E.; Wagner, A.; Liedke, M. O.

Flash lamp annealing (FLA) with millisecond pulse duration is reported as a novel curing method for pore precursors degradation in thin films. A case study on the curing of dielectric thin films is presented. FLA-cured films are being investigated by means of positron annihilation spectroscopy and Fourier-transform infrared (FTIR) spectroscopy in order to quantify the nm-scale porosity and post-treatment chemistry, respectively. Results from positron annihilation reveal the onset of formation of porous voids inside the samples at 6 ms flash treatment time. Moreover, parameter adjustment (flash duration and energy density) allows for identifying the optimum conditions of effective curing. Within such a systematic investigation, positron results indicate that FLA is able to decompose the porogen (pore precursors) and to generate interconnected (open porosity) or isolated pore networks with self-sealed pores in a controllable way. Furthermore, FTIR results demonstrate the structural evolution after FLA, that help for setting the optimal annealing conditions whereby only a residual amount of porogen remains and at the same time a well-densified matrix, and a hydrophobic porous structures are created. Raman spectroscopy suggests that the curing-induced self-sealing layer developed at the film surface is a graphene oxide-like layer, which could serve as the outside sealing of the pore network from intrusions.

Related publications

Permalink: https://www.hzdr.de/publications/Publ-36933
Publ.-Id: 36933


Preclinical Characterization of the 177Lu-Labeled Prostate Stem Cell Antigen (PSCA)-Specific Monoclonal Antibody 7F5

Striese, F.; Neuber, C.; Gräßel, S.; Arndt, C.; Ullrich, M.; Steinbach, J.; Pietzsch, J.; Bergmann, R.; Pietzsch, H.-J.; Sihver, W.; Frenz, M.; Feldmann, A.; Bachmann, M.

: Prostate specific membrane antigen (PSMA) is an excellent target for imaging and treatment of prostate carcinoma (PCa). Unfortunately, not all PCa cells express PSMA. Therefore, alternative theranostic targets are required. The membrane protein prostate stem cell antigen (PSCA) is highly overexpressed in most primary prostate carcinoma (PCa) cells and in metastatic and hor-mone refractory tumor cells. Moreover, PSCA expression positively correlates with tumor pro-gression. Therefore, it represents a potential alternative theranostic target suitable for imaging and/or radioimmunotherapy. In order to support this working hypothesis, we conjugated our previously described anti-PSCA monoclonal antibody (mAb) 7F5 with the bifunctional chelator CHX-A″-DTPA and subsequently radiolabeled it with the theranostic radionuclide 177Lu. The re-sulting radiolabeled mAb ([177Lu]Lu-CHX-A″-DTPA-7F5) was characterized both in vitro and in vivo. It showed a high radiochemical purity (>95%) and stability. The labelling did not affect its binding capability. Biodistribution studies showed a high specific tumor uptake compared to most non-targeted tissues in mice bearing PSCA-positive tumors. Accordingly, SPECT/CT images re-vealed a high tumor-to-background ratios from 16 h to 7 days after administration of [177Lu]Lu-CHX-A″-DTPA-7F5. Consequently, [177Lu]Lu-CHX-A″-DTPA-7F5 represents a promising candidate for imaging and in the future also for radioimmunotherapy.

Keywords: 177Lu-labeled antibody; prostate stem cell antigen; CHX-A’’-DTPA; prostate cancer

Permalink: https://www.hzdr.de/publications/Publ-36931
Publ.-Id: 36931


Multivalent adaptor proteins specifically target NK cells carrying a universal chimeric antigen receptor to ErbB2 (HER2)-expressing cancers

Pfeifer Serrahima, J.; Zhang, C.; Oberoi, P.; Bodden, M.; Röder, J.; Arndt, C.; Feldmann, A.; Kiefer, A.; Prüfer, M.; Kühnel, I.; Tonn, T.; Bachmann, M.; Wels, W. S.

Chimeric antigen receptor (CAR)-engineered immune effector cells constitute a promising approach for adoptive cancer immunotherapy. Nevertheless, on-target/off-tumor toxicity and immune escape due to antigen loss represent considerable challenges. These may be overcome by adaptor CARs that are selectively triggered by bispecific molecules that crosslink the CAR with a tumor-associated surface antigen. Here, we generated NK cells carrying a first- or second-generation universal CAR (UniCAR) and redirected them to tumor cells with so-called target modules (TMs) which harbor an ErbB2 (HER2)-specific antibody domain for target cell binding and the E5B9 peptide recognized by the UniCAR. To investigate differential effects of the protein design on activity, we developed homodimeric TMs with one, two or three E5B9 peptides per monomer, and binding domains either directly linked or separated by an IgG4 Fc domain. The adaptor molecules were expressed as secreted proteins in Expi293F cells, purified from culture supernatants and their bispecific binding to UniCAR and ErbB2 was confirmed by flow cytometry. In cell killing experiments, all tested TMs redirected NK cell cytotoxicity selectively to ErbB2-positive tumor cells. Nevertheless, we found considerable differences in the extent of specific cell killing depending on TM design and CAR composition, with adaptor proteins carrying two or three E5B9 epitopes being more effective when combined with NK cells expressing the first-generation UniCAR, while the second-generation UniCAR was more active in the presence of TMs with one E5B9 sequence. These results may have important implications for the further development of optimized UniCAR and target module combinations for cancer immunotherapy.

Keywords: Chimeric antigen receptor; ErbB2; HER2; NK-92; Natural killer cells; UniCAR

Permalink: https://www.hzdr.de/publications/Publ-36930
Publ.-Id: 36930


Generation of optimal weight values based on the Recursive Monte Carlo (RMC) method for using in MC deep penetrations calculations

Yadav, P.; Rachamin, R.; Konheiser, J.; Baier, S.

In nuclear engineering, Monte Carlo (MC) methods are commonly used for reactor analysis and radiation shielding problems. These methods are capable of dealing with both simple and complex system models with accuracy. The application of Monte Carlo methods experiences challenges when dealing with the deep penetration problem that is typically encountered in radiation shielding cases. It is difficult to produce statistically reliable results due to poor particle sampling in the region of interest. Therefore, such calculations are performed by the Monte Carlo N-Particle Transport (MCNP) code in association with the weight window (WW) variance reduction technique, which increases the particle statistics in the desired tally region. However, for large problems, the MCNP’s built-in weight window generator produces zero weight window parameters for the tally regions located far from the source. To address this issue, the recursive Monte Carlo (RMC) method was proposed. This paper focuses on the RMC methodology and its implementation in the HZDR’s in-house code (TRAWEI), which is responsible for producing optimal zone weight parameters used for optimizing the deep penetration MC calculations. In addition, this paper discusses the verification of the TRAWEI weight generator program to that of an existing MCNP weight window generator. The performance of TRAWEI-generated weight values is assessed using a handful of test cases involving two shield materials. Globally, the TRAWEI-generated weight values improved the statistical variance and computational efficiency of the Monte Carlo run compared to the analog MCNP simulation, and that of the simulation with weight window values generated by the standard MCNP weight window generator (WWG).

Keywords: deep penetration problem; weight window (WW); recursive Monte Carlo (RMC)

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36928
Publ.-Id: 36928


Spin–orbit coupling corrections for the GFN-xTB method

Jha, G.; Heine, T.

Spin–orbit coupling (SOC) is crucial for correct electronic structure analysis in molecules and materials, for example, in large molecular systems such as superatoms, for understanding the role of transition metals in enzymes, and when investigating the energy transfer processes in metal–organic frameworks. We extend the GFN-xTB method, popular to treat extended systems, by including SOC into the hamiltonian operator. We followed the same approach as previously reported for the density–functional tight-binding method and provide and validate the necessary parameters for all elements throughout the Periodic Table. The parameters have been obtained consistently from atomic SOC calculations using the density–functional theory. We tested them for reference structures where SOC is decisive, as in the transition metal containing heme moiety, chromophores in metal–organic frameworks, and in superatoms. Our parameterization paves the path for incorporation of SOC in the GFN-xTB based electronic structure calculations of computationally expensive molecular systems.

Keywords: Spin-Orbit Coupling; GFN-xTB; Semi-empirical method

Permalink: https://www.hzdr.de/publications/Publ-36926
Publ.-Id: 36926


Activity measurement and calculation for gamma-emitting radionuclides in concrete drill cores of unit 2 of the Greifswald NPP

Pönitz, E.; Roode-Gutzmer, Q. I.; Barkleit, A.; Konheiser, J.

Due to Germany's nuclear phase-out, decommissioning and final disposal of construction materials of Nuclear Power Plants (NPP) become increasingly important. The reliable determination of radionuclides produced by neutron activation, the activity as a function of time since shutdown and investigation of subsequent radionuclide mobility are subject of a research project. Drill cores of the concrete shielding of unit 2 of the Greifswald NPP were retrieved. Specific activities of gamma emitters and the elemental composition were measured. The radiation transport code MCNP 6 was used for the calculation of spectral neutron fluences. A neutron radiation field calculation reveals that the maximum neutron fluence in the concrete component is located in the floor just below the RPV. The concrete structures closest to the reactor core are shielded efficiently against neutron radiation by the annular water tank. Measured and calculated specific activities of 152Eu, 154Eu and 60Co for the cement screed at the position of the maximum neutron fluence are surprisingly low. A specific exemption (i.e. release from radiation protection surveillance but mandatory for final disposal) of the screed sample according to Germany’s Radiation Protection Ordnance is expected to be possible approximately 4 decades after the shutdown of the NPP.

  • Lecture (Conference)
    17th International Symposium on Reactor Dosimetry, 21.-26.05.2023, Lausanne, Schweiz

Permalink: https://www.hzdr.de/publications/Publ-36925
Publ.-Id: 36925


Modification of Three-Magnon Splitting by In-Plane Magnetic Fields

Schultheiß, K.; Körber, L.; Heins, C.; Soldatov, I.; Schäfer, R.; Kakay, A.; Schultheiß, H.

Over the past few decades, extensive research has been conducted on magnetic vortices due to their fundamental physical properties and potential applications as magnetic storage devices or resonators. Information can be encoded in the polarity or gyrotropic motion of the vortex core. Moreover, magnetic vortices offer a versatile spectrum of radial and azimuthal magnon modes, which exhibit interesting linear and nonlinear dynamics. One notable example is three-magnon splitting, where one mode can spontaneously split into two secondary magnon modes when excited above a threshold power. Three-magnon splitting follows specific selection rules, with the split modes having distinct frequencies and mode numbers to fulfill energy and angular momentum conservation [1]. Magnetic vortices offer the potential to stimulate these processes below their intrinsic threshold powers [2, 3], making them promising candidates for novel computing approaches such as reservoir computing.

In this study, we demonstrate that the application of in-plane magnetic fields in the order of a few mT can efficiently modify three-magnon splitting [4]. Using micromagntic simulations and Brillouin-light-scattering microscopy, we show that the deformation of the vortex results in additional secondary butterfly modes that follow the same selection rules as the regular modes but exhibit different localization and much lower three-magnon splitting threshold powers.

[1] K. Schultheiss et al. PRL 122, 097202 (2019)
[2] L. Körber et al. PRL 125, 207203 (2020)
[3] L. Körber et al. arXiv 2211.02328 (2022)
[4] L. Körber et al. APL 122, 092401 (2023)

Keywords: magnetic vortex; spin waves; magnons; nonlinearity

Related publications

  • Poster
    Magnonics Conference, 30.07.-3.8.2023, Le Touquet - Paris - Plague, Frankreich

Permalink: https://www.hzdr.de/publications/Publ-36924
Publ.-Id: 36924


Special Issue “Advances in Monitoring Metabolic Activities of Microorganisms by Calorimetry”

Matulis, D.; Wadsö, L.; Fahmy, K.

Editorial Special Issue “Advances in Monitoring Metabolic Activities of Microorganisms by Calorimetry”

Keywords: heavy metals; toxicity; metabolic heat; bacterial growth; antibiotics; fungal metabolism

Permalink: https://www.hzdr.de/publications/Publ-36923
Publ.-Id: 36923


Strong-field QED in Furry-picture momentum-space formulation: Ward identities and Feynman diagrams

Hernandez Acosta, U.; Kämpfer, B.

The impact of a strong electromagnetic background field on otherwise perturbative QED processes is studied in the momentum-space formulation. The univariate background field is assumed to have finite support in time, thus being suitable to provide a model for a strong laser pulse in plane-wave approximation. The usually employed Furry picture in position space must be equipped with some non-obvious terms to ensure the Ward identity. In contrast, the momentum space formulation allows for an easy and systematic account of these terms, both globally and order-by-order in the weak-field expansion. In the limit of an infinitely long-acting (monochromatic) background field, these terms become gradually suppressed, and the standard perturbative QED Feynman diagrams are recovered in the leading-order weak-field limit. A few examples of three- and four-point amplitudes are considered to demonstrate the application of our Feynman rules which employ free Dirac spinors, the free photon propagator, and the free Fermion propagator, while the external field impact is solely encoded in the Fermion-Fermion-photon vertex function. The appearance of on-/off-shell contributions, singular structures, and Oleinik resonances is pointed out.

Keywords: strong-field QED; Ward identity; laser pulses in plane-wave approximation; Feynman diagrams

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36922
Publ.-Id: 36922


Carborane-based Tebufelone Analogs and their Biological Evaluation In Vitro

Braun, S.; Paskas, S.; Laube, M.; George, S.; Hofmann, B.; Lönnecke, P.; Steinhilber, D.; Pietzsch, J.; Mijatović, S.; Maksimović-Ivanić, D.; Hey-Hawkins, E.

The presence of inflammatory mediators in the tumor microenvironment, such as cytokines, growth factors or eicosanoids, indicate cancer-related inflammatory processes. Targeting these inflammatory mediators and related signal pathways may offer a rational strategy for the treatment of cancer. This study focuses on the incorporation of metabolically stable, sterically demanding, and hydrophobic dicarba-closo-dodecaboranes (carboranes) into dual cyclooxygenase-2 (COX-2)/5-lipoxygenase (5-LO) inhibitors that are key enzymes in the biosynthesis of eicosanoids. The di-tert-butylphenol derivative tebufelone represents a selective dual COX-2/5-LO inhibitor. The incorporation of meta- or para-carborane into the tebufelone scaffold resulted in eight carborane-based tebufelone analogs that show no COX inhibition but 5-LO inhibitory activities in vitro. Cell viability studies on HT29 colon adenocarcinoma cells revealed that the para-carborane analog 8 exhibits higher anticancer activity compared to tebufelone through the inhibition of cell proliferation. Hence, this strategy proved to be a promising approach to design potent 5-LO inhibitors with potential application as cytostatic agents.

Permalink: https://www.hzdr.de/publications/Publ-36921
Publ.-Id: 36921


Basics of gas flow modulation applied to bubble columns

Marchini, S.; Schubert, M.; Hampel, U.

Bubble columns are industrial equipment used for promoting the contact between the gas and the liquid phase. In the column, the gas phase rises in form of bubbles in a pool of liquid. The fraction of the column’s volume occupied by the gas is called gas holdup. Bubble column applications include bioreactors, production of food and beverage as well as of crucial chemicals. The Axial Dispersion Model is the most accepted model for describing the gas flow in bubble columns. In this model, all phenomena deviating from plug-flow conditions are combined and indicated as dispersion. Knowledge of the axial dispersion coefficient is crucial for designing bubble column reactors. This study provides a new non-invasive approach for measuring axial gas dispersion coefficients in bubble column reactors and the application of the new approach at different operating conditions.

  • Poster
    Doctoral Seminar of HZDR, 19.-21.10.2022, Wroclaw, Poland

Permalink: https://www.hzdr.de/publications/Publ-36920
Publ.-Id: 36920


Flow and mass transfer in structured packings with modified surfaces

Giustacori, P.; Brunazzi, E.; Schubert, M.; Shabanilemraski, I.; Marchini, S.

Commonly, structured packings are operated in film flow. In this case, the entire surface of the packing is completely covered by the liquid to make maximum
use of the available surface area on the elements. However, perfect wetting of the packing is usually difficult to achieve. Moreover, when film flow is targeted, the interfacial area cannot exceed the geometric surface area provided by the packing. Thus, other flow configurations must be alternatively considered increasing the interfacial area potentially available for mass transfer. Droplet flow is one way to achieve this goal. Considering the extreme case of a spherical droplet in contact with the packing on a single infinitesimally small point. For equal volume of droplet and film, the interfacial area in this case is almost five times higher compared to film flow. The developed work is meant to characterize flow structures alternative to the classical film flow over structured packings to determine potential improvement in mass transfer performances. To achieve changes in the flow structure, the surface of the packings elements was modified. In particular, surface treatments were used to improve the hydrophobic properties of the surface. In this way, the formation of liquid droplets on the surface was promoted. A preliminary literature review allowed the selection of self-assembled monolayers (SAMs) as surface modification methods due to the simplicity of performing the treatment. A characterization campaign of the modified surfaces was carried out. Smooth metal sheets specimens of which the packings are made were used for the investigation of contact angles via optical techniques. Behavior of obtained droplets and rivulets as well as their tendency to coalesce were also analyzed. Subsequently, the mass transfer performance of the modified packings was compared with that of the standard packings by air-led stripping of isobutyl acetate from an aqueous solution. A model was developed in this work for droplet and rivulet flow in order to determine specific surface area from packings characteristic and liquid flow rate. Experimental liquid holdup values were used as reference parameter for model validation. This work showed that the considered packing coated with the selected SAMs has a worse performance compared to the non-coated packing in terms of liquid holdup and mass transfer performance, at least when tested with aqueous solutions. However, the value of the present work mainly consists of the developed mathematical model and procedure for packing characterization and performance comparison. In fact, this will allow characterization of possible other surface treatments applicable to the surfaces of structured packings.

Keywords: structured packing; Self-assembling monolayers; droplets; surface modification; mass transfer study

  • Master thesis
    University of Pisa, 2023
    Mentor: Schubert, Markus; Marchini, Sara; Brunazzi, Elisabetta; Shabanilemraski, Iman
    117 Seiten

Permalink: https://www.hzdr.de/publications/Publ-36919
Publ.-Id: 36919


Experimental and Numerical Investigation of a Counter-Current Flow Bubble Column

Khan, H.; Kováts, P.; Zähringer, K.; Rzehak, R.

Bubble columns are gas-liquid contactors that are used in many process-engineering applications. A counter-current liquid flow is frequently imposed to adjust the bubbles’ residence-time and thus optimize mixing and mass-transfer. The present work describes measurements in such a device together with corresponding computational fluid dynamics simulations based on the Eulerian two-fluid framework. Bubble-size and -velocity are measured by shadow-imaging for a large range of gas and counter-current liquid flow rates, as well as different nozzle sizes. The corresponding liquid flow-fields are characterized by Particle Image Velocimetry. From the large experimental database, a few cases are selected to analyze the flow structure and effects of the bubble-size. In the simulations, different models for the drag- and lift-force acting on the bubbles are evaluated. While good agreement between experiments and simulations could be achieved for the gas-fraction and gas-velocity, differences are found for the liquid-velocity, which is generally overestimated in the calculations.

Keywords: countercurrent flow bubble column; shadowgraphy; PIV; Euler-Euler two-fluid model; CFD simulation

Downloads

  • Secondary publication expected from 09.12.2024

Permalink: https://www.hzdr.de/publications/Publ-36918
Publ.-Id: 36918


The application of encoder–decoder neural networks in high accuracy and efficiency slit-scan emittance measurements

Ma, S.; Arnold, A.; Michel, P.; Murcek, P.; Ryzhov, A.; Schaber, J.; Steinbrück, R.; Evtushenko, P.; Teichert, J.; Hillert, W.; Xiang, R.; Zhu, J.

A superconducting radio-frequency (SRF) photo injector is in operation at the electron linac for beams with high brilliance
and low emittance (ELBE) radiation center and generates continuous wave (CW) electron beams with high average current
and high brightness for user operation since 2018. The speed of emittance measurement at the SRF gun beamline can be
increased by improving the slit-scan system, thus the measurement time for one phase space mapping can be shortened
from about 15 min to 90 s. The convolution neural networks are applied to improve the efficiency and accuracy of beamlet
images processing. In order to estimate the uncertainty in the calculation of normalized emittance, we analyze the main error
contributions.

Keywords: Beam emittance; Machine learning; Slit-scan; SRF photo injectors

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36917
Publ.-Id: 36917


Machine learning-based characterization of collected black carbon and desert dust using HIM microscopy supporting real-time Aethalometer measurements

Podlipec, R.; Lohman, S.; Ivančič, M.; Alföldy, B.; Gregorič, A.; Rigler, M.; Mahfouz, M. M. K.; Pandolfi, M.; Munnik, F.; Heller, R.

Accurate physical and chemical characterization of the aerosols from various sources, such as urban/industrial emissions, biomass burning to dust intrusion events, paramount to unveiling the impact on air quality, radiative forcing and public health, still presents a big challenge. The first step to assess the impact of aerosols is real-time light absorption measurements, typically characterizing spectral dependence with an absorption Angstrom exponent (AAE) approach (Liu et al 2018). Using new model of Aethalometer, AE36s (Aerosol Magee Scientific), with an enhanced spectral resolution, further helps with improved characterization and distinction between different collected aerosols revealing several specific events and sources of aerosol emission. Unfortunately, filter photometers cannot be equipped with analysers which would uncover the distribution and physicochemical properties of collected aerosols on single particle scale, important for an accurate interpretation of the real-time measurements. In the presented study we show for the first time capability of successfully implementing machine learning-based smart characterization of collected aerosols from dust intrusion events in Europe (Barcelona, Ljubljana) and the Middle East (Qatar), to support real-time Aethalometer measurements indicating significant black carbon (BC) and absorbing fraction of organic aerosols (brown carbon, BrC) presence. Briefly, quartz fiber filters with collected aerosols were transferred from the measuring sites to the imaging instrument, Helium Ion Microscope (HIM), which provides unique properties: sub-nm lateral resolution, nm surface sensitivity and high depth-of-field (Hlawacek et al 2014), enabling imaging of aerosols deep into the fibers (Figure 1), not capable with Scanning Electron Microscope (SEM). Imaging at different magnifications enabled accurate analysis of aerosol concentration, size distribution and detection of morphologies at a single particle scale. Imaging contrast sensitive to particle physiochemical properties enabled the distinction of BC from mineral dust, which provided quantification of both separately, using machine learning registration, segmentation and object classification done by Ilastik open-source software (Figure 2).
The results of this approach gave insights into diverse aerosol properties from mm down to nm scale and support real-time optical absorption measurements, key for accurate characterization and for predicting the environmental and health impact of sampled polluted air.

Related publications

  • Lecture (Conference)
    European Aerosol Conference 2023 (EAC 2023), 03.-08.09.2023, Malaga, Spain

Permalink: https://www.hzdr.de/publications/Publ-36915
Publ.-Id: 36915


Early mechanisms of ultrafine particulate matter toxicity on in vitro lung model by advanced correlative microscopies

Podlipec, R.; Krišelj, A.; Pirker, L.; Urbančič, I.; Štrancar, J.; Hlawacek, G.

A comprehensive understanding of molecular events leading to adverse outcomes in lungs after administration of ultrafine particulate matter (PM) is still lacking. These repeating exposures to the respiratory tract can eventually lead to persistent inflammation and further cardiovascular diseases (Li et al 2019, Underwood 2017). To better identify and characterize the initial sub-cellular to molecular events after nanomaterial contact, which triggers all following cascades leading to acute or even chronic inflammation, one urgently needs an appropriate high-resolution experimental approach to untangle these key processes.
In our first study focused on how metal oxide aerosols (TiO2) effect model lung epithelium we thus applied super-resolution STED microscopy together with fluorescence microspectroscopy (FMS), where we showed nanoparticle wrapping of cell membranes followed by their translocation across the cell layer (Figure 1) supporting the proposed causal link between the inhalation of nanoparticles and cardiovascular disease (Urbančič et al 2018). But to get more insight into complex and likely destructive nanoparticle interaction with biological matter our next aim was to identify and characterize individual paramount cellular responses by observing real-time structural changes implementing advanced correlative microscopy (CM) approach.
In one of our latest studies, we thus introduced a new CM pipeline, combining STED multimodal microscopy with helium ion microscopy (HIM), which revealed the morphology and the extent of biological wrapping of quarantined nanomaterial composites on the epithelium surface decisive for the onset of chronic inflammation on single molecule scale (Kokot et al 2020) (Figure 2).

Related publications

  • Lecture (Conference)
    European Aerosol Conference 2023 (EAC 2023), 03.-08.09.2023, Malaga, Spain

Permalink: https://www.hzdr.de/publications/Publ-36914
Publ.-Id: 36914


Different effect of anatase TiO2 nanotubes and nanocubes on microtubule fragmentation, mitotic arrest and aneuploidy indicating plausible carcinogenicity

Podlipec, R.; Hlawacek, G.

Ultra-high resolution Helium Ion Microscopy (HIM) images of lung epithelial cells exposed to titanium dioxide (TiO2) nanotubes. Images reveal cell nuclear envelope with nuclear pores and cytoskeleton structure showing local damage at the site with the presence of single TiO2 nanotubes. 

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36913
Publ.-Id: 36913


Study of hydrodynamics in counter current bubble column

Khan, H.; Rzehak, R.; Kováts, P.; Zähringer, K.

Bubble column reactors are one of the simplest and most representative system for multiphase flows. Regardless of its simple geometry, complex hydrodynamics and its effect on transport properties requires better understanding in order to accomplish a reliable design and scale-up of bubble column reactors. Although with many other parameters, co- or counter-current liquid flow is often used to adjust the residence-time of the bubbles, which is especially important when mass transfer is present in the system. The present study comprises of the initial stage numerical effort to study the hydrodynamics and also the parametric effect in counter current bubble column. For this purpose, simulations are performed within the Eulerian two-fluid framework using OpenFOAM as a CFD software and later the results are being compared with the experimental data.

Keywords: bubble column; dispersed two-phase flow; closure relations; countercurrent flow; Euler-Euler simulation

  • Lecture (Conference)
    11th International Conference on Multiphase Flow, ICMF 2023, 02.-07.04.2023, Kobe, Japan

Permalink: https://www.hzdr.de/publications/Publ-36912
Publ.-Id: 36912


Different effect of anatase TiO2 nanotubes and nanocubes on microtubule fragmentation, mitotic arrest and aneuploidy indicating plausible carcinogenicity

Podlipec, R.

Time-lapse videos of cells and microtubule dynamics (in green) after exposure to different nanoparticles (in red) taken with confocal fluorescence microscopy. S1 - control experiment; S2-S3 - the exposure to titanium dioxide (TiO2) nanotubes measured at different image planes; S4-S5 - the exposure to TiO2 nanocubes measured at different image planes; S6-S7 - the exposure to multiwall carbon nanotubes (MWCNTs) measured at different image planes.

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36911
Publ.-Id: 36911


Data publication: Selective removal of Gallium from mixed metal solutions with Arsenic by ion flotation using the biosurfactant rhamnolipid

Chakankar, M. V.; Pollmann, K.; Rudolph, M.

Rhamnolipids have received great attention in various environmental applications in terms of metal complexation and recovery. However, the influence of metal ions on the interfacial, foaming, and ion flotation properties of rhamnolipid are poorly investigated. In this study we investigated the effect of metal ions alone and in a mixed metal system on the interfacial and foaming properties of rhamnolipid. Further, the potential of rhamnolipid to recover and separate Gallium from a mixed metal system containing Gallium (Ga) and Arsenic (As) using bioionflotation has been investigated. The effect of operating parameters like pH, rhamnolipid concentration, and airflow rate were tested and found to have a significant influence on the separation performance. The maximum removal of Ga could reach 74 % when rhamnolipid concentration was 0.85 mM at pH 6 and an airflow rate of 80 ml/min. The selectivity index of Ga over As was highest (17.2) at 0.85 mM rhamnolipid concentration, pH 6, and an airflow rate of 40 ml/min. Also, the selective separation of Ga was dependent on the recovery of water from the foam. The results showed that rhamnolipid biosurfactant acted as a highly efficient ion collector for Ga and the optimized process parameters could be expected to provide very efficient separation and recovery of target metal via ion flotation.

Keywords: Rhamnolipid; gallium; arsenic; ion flotation; selectivity; metal recovery; water recovery

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36908
Publ.-Id: 36908


Development of Carborane-Based Ligands for PET and SPECT Imaging

Ueberham, L.; Moldovan, R.-P.; Deuther-Conrad, W.; Gündel, D.; Brust, P.; Kopka, K.; Laube, M.; Pietzsch, J.; Hey-Hawkins, E.

The early detection of diseases like Alzheimer, Parkinson or cancer have gained importance over the last decade, since they are still the cause of death of millions of people worldwide.[1] To screen patients for disease markers, non-invasive imaging techniques like Positron Emission Tomography (PET) and Single-photon Emission Computed Tomography (SPECT) are suitable methods for diagnostics.[2]
Radiopharmaceuticals with ligands of high affinity and selectivity towards the targets involved in the maladies, like the cannabinoid receptor type 2 (CB2R) or cyclooxygenase 2 (COX-2) have to be developed. In addition to high affinity and selectivity, other requirements are also high metabolic stability or balanced hydrophobicity.[2,3]
The development of such radioligands is a challenge; for example, no CB2R radioligand is available for routine clinical applications so far. To overcome the lack in metabolic stability and increase the selectivity of suitable ligands, closo-dicarbadodecaboranes (carboranes) are employed. The hydrophobic carborane can be introduced as a replacement for phenyl, cyclohexyl or adamantyl groups, to name but a few.[4]
A new class of ligands based on (metalla)carboranes for application in PET and SPECT imaging for investigation of CB2R and COX-2 have been synthesized and in part biologically evaluated. These results will be presented and discussed in detail.

  • Poster
    Wissenschaftsforum GDCH, 04.-06.09.2023, Leipzig, Germany

Permalink: https://www.hzdr.de/publications/Publ-36906
Publ.-Id: 36906


Mirror twin boundaries in WSe2 induced by vanadium doping

Pathirage, V.; Lasek, K.; Krasheninnikov, A.; Komsa, H. P.; Batzill, M.

Mirror twin boundaries (MTBs) observed in MoSe2 are formed due to incorporation of excess Mo into the lattice. In contrast, MTBs in WSe2 have a high formation energy and consequently are not present in this system. Here we show that V-doping of WSe2, achieved by co-deposition of V and W during molecular beam epitaxy (MBE) growth of WSe2, can also induce MTB formation in WSe2, as revealed by scanning tunneling microscopy. Our experimental results are supported by density functional theory calculations that show that V-doped WSe2 is susceptible to the incorporation of more V-atoms at interstitial sites. This increases the transition metal atom concentration in the lattice, and these excess atoms rearrange into MTBs, which is associated with energy lowering of the excess metal atoms. While formation of MTBs gives rise to the pinning of the Fermi-level and thus prevents V-induced electronic doping, MTBs do not appear to affect the magnetic properties, and a diluted ferromagnetic material is observed for low V- doping levels, as reported previously for V-doped WSe2.

Keywords: 2D materials; doping

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36905
Publ.-Id: 36905


Velocity distributions of particles sputtered from supported two-dimensional MoS2 during highly charged ion irradiation

Skopinski, L.; Kretschmer, S.; Ernst, P.; Herder, M.; Madauß, L.; Breuer, L.; Krasheninnikov, A.; Schleberger, M.

A key problem in ion-solid interaction is the lack of experimental access to the dynamics of the processes. While it is clear
that the mechanisms of interaction and sputtering depend on the kinetic and potential energy (sum of ionization energies) of
the projectile, the importance and interplay of the various interaction mechanisms are unknown. Here, we have irradiated
substrate-supported (Au, SiO2) monolayers of MoS2 with highly charged xenon ions (HCIs; charge state: 17+ to 40+),
extracted the emitted neutral postionized Mo particles in a time-of-flight mass spectrometer, and determined their velocity
distributions. We find two main contributions, one at high velocities and a second at lower velocities, and assign them to
kinetic and potential effects, respectively. We show that for slow HCIs (5 keV) the interaction mechanisms leading to particle
emission by electronic excitation and momentum transfer, respectively, are independent of each other, which is consistent
with our atomistic simulations. Our data suggest that the predominant mechanism for potential sputtering is related to
electron-phonon coupling, while nonthermal processes do not play a significant role. We anticipate that our work will be a
starting point for further experiments and simulations to better understand the interplay of processes arising from Epot and
Ekin.

Keywords: Ion bombardment; Ions; Xenon Ions; Velocity distribution; Charge state; Distribution of particles; Highly charged ions; Interaction mechanisms; Ion-solid interactions; Ions irradiation; Two-dimensional; Layered semiconductors; Gold; Molybdenum; Sulfur compounds; Au/SiO2; Silica; Mass spectrometers

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36904
Publ.-Id: 36904


microscenery: stage explorer

Tiemann, J.; Michel, K.; McGinity, M.; Sbalzarini, I. F.; Günther, U.

In 3D microscopy, aligning the sample and region of interest can consume precious photon budget, time or other
resources which, as in the case of experiments with high throughput or short sample life span, are often limited.
To remedy this, additional overview cameras and 2D “stage explorer” software are often used, allowing rapid high-level
search and alignment of samples. However, such systems are not always available, or may not support 3D stage
exploration, which may be a critical requirement for certain experiments.
To alleviate this problem we present microscenery: stage explorer, an open-source 3D stage explorer system with
support for Virtual Reality (VR) and live microscope control.
Our software allows the experimenter to control the stage position along all three spatial axes and acquire images. In
addition to the traditional mouse and keyboard interface, our system natively supports VR display and interaction.
Virtual Reality can often provide improved spatial understanding and manipulation of 3D data, accelerating stage
exploration. In addition, manipulating a 3D stage can be easier and more intuitive with 3D hand tracking or 3D input
devices than with a traditional 2D mouse and keyboard interface.
In microscenery stage explorer, the user controls the microscope and views acquired images from within VR. Images are
displayed in a virtual 3D stage space with the correct real-world spatial relations to each other. If the pixel-to-
micrometer ratio is known and a precise stage is used, a seamlessly stitched image readily emerges, in realtime, as the
user explores the stage space, allowing the user to rapidly navigate large samples. For setups where the physical size
of the sample is small, large magnification is used, or multiple samples are mounted, our software helps navigate the
stage space and find the samples more easily.
In addition to manual sampling, we have also implemented two automated sampling functions. The first is full-stack
acquisition, in which an image stack is automatically obtained and rendered at the correct position by 3D volume
rendering. In the second, the stage space can be explored automatically. Here, the experimenter specifies a cubic
search area which our application then automatically samples at regular intervals. In both cases, the usable and safely
accessible stage space can be defined before use, both to reduce the search space and to observe limits of the
hardware.
Currently, microscenery: stage explorer targets light-sheet microscopes, but generally any system that is controllable
with MicroManager is supported. It connects to MicroManager via a plugin and can be run on the same machine or over
the network. It can therefore be used as an extension to existing MicroManager workflows. Our system currently
supports head-mounted VR displays, with support for CAVE systems in development

Keywords: Virtual Reality; Lightsheet microscopy; Instrument control; visualisation; microscopy

  • Poster
    Focus on Microscopy, 02.04.-05.05.2023, Porto, Portugal

Permalink: https://www.hzdr.de/publications/Publ-36903
Publ.-Id: 36903


Investigation of RPV samples of the Greifswald NPP with focus on retrospective dosimetry

Pönitz, E.; Konheiser, J.

Reactor pressure vessel (RPV) samples of units 1 and 4 of the Greifswald NPP were investigated with focus on retrospective dosimetry. Specific activities of long-lived radionuclides 63Ni, 93mNb, 94Nb and 99Tc as well as the concentrations of the producing elements were measured. Investigated samples comprise base metal, welding metal and cladding of the RPV. Neutron fluences obtained with the Monte-Carlo codes TRAMO and MCNP were used to calculate specific activities. The gamma-emitter 94Nb appears as a promising candidate due to the large Nb concentration in the cladding of the VVER RPVs. For 93mNb, a very good agreement of measured und calculated activities was found for the RPV cladding samples where 93mNb is primarily produced by the threshold reaction 93Nb(n,n’)93mNb. A strong scatter of the ratios of calculated and experimental activities is observed for 63Ni which is primarily produced by slow neutrons. For 99Tc, a good agreement of calculated and measured activities was found for the majority of the base metal and welding metal samples but not for the cladding samples. Updated reaction cross section data for 62Ni(n,γ) and 92Mo(n,γ) lead to a better agreement of calculated and measured activities for 63Ni and 93mNb.

  • Poster
    17th International Symposium on Reactor Dosimetry, 21.-26.05.2023, Lausanne, Schweiz

Permalink: https://www.hzdr.de/publications/Publ-36902
Publ.-Id: 36902


Progress in Hybrid Plasma Wakefield Acceleration

Hidding, B.; Assmann, R.; Bussmann, M.; Campbell, D.; Chang, Y.-Y.; Corde, S.; Couperus Cabadağ, J. P.; Debus, A.; Döpp, A.; Gilljohann, M.; Götzfried, J.; Moritz Foerster, F.; Haberstroh, F.; Habib, F.; Heinemann, T.; Hollatz, D.; Irman, A.; Kaluza, M.; Karsch, S.; Kononenko, O.; Knetsch, A.; Kurz, T.; Kuschel, S.; Köhler, A.; Martinez De La Ossa, A.; Nutter, A.; Pausch, R.; Raj, G.; Schramm, U.; Schöbel, S.; Seidel, A.; Steiniger, K.; Ufer, P.; Yeung, M.; Zarini, O.; Zepf, M.

Plasma wakefield accelerators can be driven either by intense laser pulses (LWFA) or by intense particle beams (PWFA). A third approach that combines the complementary advantages of both types of plasma wakefield accelerator has been established with increasing success over the last decade and is called hybrid LWFA→PWFA. Essentially, a compact LWFA is exploited to produce an energetic, high-current electron beam as a driver for a subsequent PWFA stage, which, in turn, is exploited for phase-constant, inherently laser-synchronized, quasi-static acceleration over extended acceleration lengths. The sum is greater than its parts: the approach not only provides a compact, cost-effective alternative to linac-driven PWFA for exploitation of PWFA and its advantages for acceleration and high-brightness beam generation, but extends the parameter range accessible for PWFA and, through the added benefit of co-location of inherently synchronized laser pulses, enables high-precision pump/probing, injection, seeding and unique experimental constellations, e.g., for beam coordination and collision experiments. We report on the accelerating progress of the approach achieved in a series of collaborative experiments and discuss future prospects and potential impact.

Keywords: plasma wakefield acceleration; LWFA; PWFA; compact particle acceleration; radiation sources

Related publications

Permalink: https://www.hzdr.de/publications/Publ-36901
Publ.-Id: 36901


Universal radiation tolerant semiconductor

Azarov, A.; Fernández, J. G.; Zhao, J.; Djurabekova, F.; He, H.; He, R.; Prytz, Ø.; Vines, L.; Bektas, U.; Chekhonin, P.; Klingner, N.; Hlawacek, G.; Kuznetsov, A.

Radiation tolerance is determined as an ability of crystalline materials to withstand the accumulation of the radiation induced disorder. Based on the magnitudes of such disorder levels, semiconductors are commonly grouped into the low- or high-radiation tolerant. Nevertheless, upon exposing to sufficiently high fluences, in all cases known by far, it ends up with either extremely high disorder levels or amorphization. Here we show that gamma/beta double polymorph Ga2O3 structures exhibit unprecedently high radiation tolerance. Specifically, for room temperature experiments, they tolerate a disorder equivalent to hundreds of displacements per atom, without severe degradations of crystallinity; in comparison with, e.g., Si amorphizable already with the lattice atoms displaced just once. We explain this behavior by an interesting combination of the Ga- and O-sublattice properties in gamma-Ga2O3. In particular, O-sublattice exhibits a strong recrystallization trend to recover the face-centered-cubic stacking despite high mobility of O atoms in collision cascades compared to Ga. Concurrently, the characteristic structure of the Ga-sublattice is nearly insensitive to the accumulated disorder. Jointly it explains macroscopically negligible structural deformations in gamma-Ga2O3 observed in experiment. Notably, we also explained the origin of the beta-to-gamma Ga2O3 transformation, as a function of increased disorder in beta-Ga2O3 and studied the phenomena as a function of the chemical nature of the implanted atoms. As a result, we conclude that gamma-beta double polymorph Ga2O3 structures, in terms of their radiation tolerance properties, benchmark a new class of universal radiation tolerant semiconductors.

Keywords: FIB; Ga2O3; Nanostructure; Polymorph; HIM; EBSD

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36900
Publ.-Id: 36900


Ultrathin positively charged electrode skin for durable anion-intercalation battery chemistries

Sabaghi, D.; Wang, Z.; Bhauriyal, P.; Lu, Q.; Morag, A.; Mikhailovia, D.; Hashemi, P.; Li, D.; Neumann, C.; Liao, Z.; Dominic, A. M.; Nia, A. S.; Dong, R.; Zschech, E.; Turchanin, A.; Heine, T.; Yu, M.; Feng, X.

The anion-intercalation chemistries of graphite have the potential to construct batteries with promising energy and power breakthroughs. Here, we report the use of an ultrathin, positively charged two-dimensional poly(pyridinium salt) membrane (C2DP) as the graphite electrode skin to overcome the critical durability problem. Large-area C2DP enables the conformal coating on the graphite electrode, remarkably alleviating the electrolyte. Meanwhile, the dense face-on oriented single crystals with ultrathin thickness and cationic backbones allow C2DP with high anion-transport capability and selectivity. Such desirable anion-transport properties of C2DP prevent the cation/solvent co-intercalation into the graphite electrode and suppress the consequent structure collapse. An impressive PF6−-intercalation durability is demonstrated for the C2DP-covered graphite electrode, with capacity retention of 92.8% after 1000 cycles at 1 C and Coulombic efficiencies of > 99%. The feasibility of constructing artificial ion-regulating electrode skins with precisely customized two-dimensional polymers offers viable means to promote problematic battery chemistries.

Keywords: batteries; dft; 2d polymers

Permalink: https://www.hzdr.de/publications/Publ-36899
Publ.-Id: 36899


Thermal and Radiation Stability of (Zr0.95241Am0.05)1-xNdxO2-x0.5 Phases: Updates from the RISE-241 ActUsLab JRC Project

Huittinen, N. M.; Gilson, S.; Popa, K.; Valu, O.; Colle, J.-Y.; Walter, O.; Murphy, G. L.

The thermal and radiation stability of Zircaloy cladding material that houses spent nuclear fuel (SNF) is an important factor when considering the safe storage and eventual disposal of SNF in a geological repository. It is known that on the surface of the cladding, oxidised zirconia (ZrO2) phases are inherently present. Following fuel swelling and rim contact, the zirconia layer on the interior surface can interact with SNF elements, leading to the formation of phases such as pyrochlore, A2Zr2O7, and other zirconates, A2ZrO3 , among others. These phases essentially act as the first intermediate barrier between the SNF and the metallic cladding and consequently are important to consider in safety design, particularly for transport/release of radionuclides (RNs). A pertinent RN that contributes significantly to the radiological hazard of SNF, is the minor actinide isotope Am-241. The chemistry of Am is largely unique, being able to readily dissociate between its tetravalent and trivalent states in oxides, making it difficult to investigate via surrogate studies using lanthanides. Furthermore, Am-241 has a relatively short t1/2 of 432 years and decays via alpha emission (5.486 MeV), resulting in significant ensuing radiation damage in host materials. Consequentially, understanding the thermal and radiation stability of host material phases incorporating Am-241 is a pertinent endeavor for safety and disposal of SNF. As a part of the national project “AcE” funded by the German Federal Ministry of Education and Research (BMBF) and through the European Commission ActUsLab program, we have investigated several zirconium oxide polymorphs, including but not limited to Nd-pyrochlore and zirconia, doped with 5 mol% Am-241. The particular focus of the investigation is to understand the thermal and radiation stability of the different oxide polymorphs when Am-241 is incorporated. This presentation will highlight a number of on-going results from this research program, including high-temperature phase transformations, radiation induced lattice swelling, phase separation, and associated apparent redox activity induced by the presence of Am-241.

  • Poster
    47th Scientific Basis for Nuclear Waste Management (SBNWM), 06.-10.11.2023, Cologne, Germany

Permalink: https://www.hzdr.de/publications/Publ-36898
Publ.-Id: 36898


High-Order Curvilinear Arbitrary Lagrangian-Eulerian MHD

Nikl, J.; Kuchařík, M.; Cangi, A.

Two-temperature resistive magnetohydrodynamics can model magnetized collisional plasmas present in inertial confinement fusion (ICF) experiments. In particular, Lagrangian methods excel in problems with strong compression or expansion, since the computational mesh follows the flow of the matter. However, simulations may loose precision, become unfeasible or even crash due to severely distorted or entangled meshes. A remedy is provided by the Arbitrary Lagrangian-Eulerian (ALE) method consisting of normal Lagrangian step(s), rezoning for regularization or untangling of the computational mesh, and remapping of the quantities from the old mesh to the new one. This procedure enables robust and precise simulations of ICF with the effects of magnetic field. We develop such a method for resistive two-temperature MHD. Unlike classical approaches, it conserves the magnetic flux and maintains the divergence-free structure of the magnetic field. Moreover, the numerical method is based on high-order curvilinear finite elements.

  • Poster
    Direct Drive and Fast Ignition Workshop 2023, 03.-05.05.2023, Oxford, United Kingdom

Permalink: https://www.hzdr.de/publications/Publ-36897
Publ.-Id: 36897


Spectral characterisation of hydrothermal alteration associated with sediment-hosted Cu–Ag mineralisation in the central European Kupferschiefer

Géring, L.; Kirsch, M.; Thiele, S. T.; de Lima Ribeiro, A.; Gloaguen, R.; Gutzmer, J.

The analysis of hydrothermal alteration in exploration drill cores allows for fluid-rock interaction processes to be traced, for fluid flow paths to be identified, and thus for vectors in mineral systems to be determined. Hyperspectral imaging techniques are increasingly being employed to fill the scale gap between lab-based petrographic or geochemical analyses and the typical size of exploration targets. Hyperspectral imaging permits the rapid, cost-efficient, and continuous characterisation of alteration mineralogy and texture along entire drill cores, with a spatial sampling of a few millimetres. In this contribution, we present the results of an exploratory study on three mineralised drill cores from the Spremberg-Graustein Kupferschiefer-type Cu-Ag deposit in the Lusatia region of Germany. We demonstrate that hyperspectral imaging is well-suited to recognising and tracking the effects of hydrothermal alteration associated with strata-bound hydrothermal mineralisation. Micro X-ray fluorescence spectrometry was used to corroborate the alteration mineral assemblages identified in hyperspectral data acquired in the visible, near- (400 to 970 nm), shortwave (970 to 2500 nm), mid-wave (2700 to 5300 nm), and longwave infrared (7700 to 12300 nm). We identified two main shortcomings of the technique, namely the overlapping of some mineral features (e.g. carbonate and illite absorption in the shortwave infrared) and the darkness of the organic-matter-rich dolostones and shales that results in low reflectance. Nevertheless, spectral features associated with iron oxide, kaolinite, sulfate, and carbonates were successfully identified and mapped. We identified different markers of hydrothermal alteration spatially associated with or stratigraphically adjacent to Cu-Ag mineralisation. Importantly, we can clearly distinguish two mineralogically distinct styles of alteration (hematite and ferroan carbonate) that bracket high-grade Cu-Ag mineralisation. Intensive hydrothermal alteration is characterised by the occurrence of well-crystallised kaolinite in the sandstone units immediately below the Kupferschiefer horizon sensu stricto. Proximal Fe-carbonate and kaolinite alteration have not previously been documented for the high-grade Cu-Ag deposits of the central European Kupferschiefer, whereas hematite alteration is well-known in Kupferschiefer-type ore deposits. The latter marks the flow path of oxidising, metal-bearing hydrothermal fluids towards the site of hydrothermal sulfide mineralisation. In contrast, ferroan carbonate alteration in carbonate rocks located above the main mineralised zone is interpreted as a mark of hydrothermal fluid discharge from the mineralising system. Although this study is limited to a small number of drill cores, our results suggest that hyperspectral imaging techniques may be used to identify vectors towards high-grade Cu-Ag mineralisation in Kupferschiefer-type mineral systems.

Keywords: Hyperspectral; Mineral deposits; Drill core; Exploration; Alteration

Permalink: https://www.hzdr.de/publications/Publ-36896
Publ.-Id: 36896


Advancements of ELBE Timing System Upgrade

Kuntzsch, M.; Zenker, K.; Schwarz, A.; Justus, M.; Hrovatin, R.;  Peruško, L.;  Legat, U.;  Rojec, U.; Oven, Z.; Krmpotić, L.

Modern Big physics experiments call for optimizations of machines in various aspects. Integration of an advanced control system is one of them, and timing system as controls’ backbone is most often required to be upgraded significantly or even designed and implemented anew. The complexity of experiments at HZDR ELBE and the range of varieties of its instruments and subsystems is combined with top-notch performance requirements. These, coupled with hardware obsolescence, dictate an implementation of an advanced timing system, surpassing a system, that was designed initially. The new timing system must be compatible with all existing timing triggering patterns and must provide configuration option for new features. It is designed to generate trigger patterns for shot on demand to 26 MHz cw which requires a universal and complex implementation of the pattern composition and validity checks. The design of this timing solution further demands the adaptation and the modification of the event-based timing system built on MRF HW. As a result, we realized the new Control Software with an extended range of functionalities. While maintaining the common functionality we made it suitable for the most demanding experiments today.

Keywords: ELBE

Related publications

  • Poster
    14th International Particle Accelerator Conference, 07.-12.05.2023, Venice, Italy
  • Contribution to proceedings
    14th International Particle Accelerator Conference, 07.-12.05.2023, Venice, Italy

Permalink: https://www.hzdr.de/publications/Publ-36895
Publ.-Id: 36895


MePS – the Mono-Energetic Positron Source for annihilation lifetime spectroscopy

Wagner, A.; Butterling, M.; Hirschmann, E.; Jungmann, M.; Liedke, M. O.; Krause-Rehberg, R.

The Helmholtz-Center Dresden - Rossendorf operates several user beamlines for materials research using positron-annihilation energy and lifetime spectroscopy. The superconducting electron linear accelerator ELBE drives several secondary beams including hard X-ray production from electron-bremsstrahlung, which serves as an intense source of positrons by means of pair production. The Mono-energetic Positron Source MePS [1] utilizes positrons with variable kinetic energies ranging from 0.5 to 18 keV for depth profiling of atomic defects and porosities on nm-scales in thin films. High timing resolutions (σt ≈100 ps) at high average event rates in excess of 105 s-1 and adjustable beam repetition rates allow performing high-throughput positron annihilation lifetime experiments. Acquiring an annihilation lifetime spectrum with 107 events takes about 80 s which paves the way to perform in-situ PALS experiments on dynamical defect evolution, migration and annealing [2,3,4].
We will present the actual status of the MePS facility and updates which are on the way. A recently constructed sample chamber will allow for fast and automated sample transfers, an increased sample temperature range (80 K to 800 K), and possibilities for sample illuminations with light sources (LED, Laser, and a broadband short arc Xe light source).
The facility is part of the ELBE Center for High-Power Radiation Sources which operates several secondary beam lines for international users.

The MePS facility has partly been funded by the Federal Ministry of Education and Research (BMBF) with the grant PosiAnalyse (05K2013). Trans-national access is available through the EU-Horizon project ReMADE for academic and industry.

[1] A. Wagner, et al., AIP Conf. Proc. 1970, 040003 (2018)
[2] L. Chiari, et al., Acta Mater. 219, 117264 (2021)
[3] M. Wenskat, et al., Sci. Rep. 10, 8300 (2020)
[4] M. Wenskat, et al., Phys. Rev. B 106, 094516 (2022)
[5] ReMADE, https://remade-project.eu/

Keywords: positron annihilation; materials science; lifetime spectroscopy

Related publications

  • Invited lecture (Conferences)
    16th International Workshop on Slow Positron Beam Techniques & Applications (SLOPOS-16), 16.-21.07.2023, Orléans, France

Permalink: https://www.hzdr.de/publications/Publ-36894
Publ.-Id: 36894


Recruiting Unicellular Algae for the Mass Production of Nanostructured Perovskites

Kuhrts, L.; Helmbrecht, L.; Noorduin, W. L.; Pohl, D.; Sun, X.; Palatnik, A.; Wetzker, C.; Jantschke, A.; Schlierf, M.; Zlotnikov, I.

Functional capacities of lead halide perovskites are strongly dependent on their morphology, crystallographic texture, and internal ultrastructure on the nano- and the meso-scale. In the last decade, significant efforts are directed towards the development of novel synthesis routes that would overcome the morphological constraints provided by the physical and crystallographic properties of these materials. In contrast, various living organisms, such as unicellular algae, have the ability to mold biogenic crystals into a vast variety of intricate nano-architectured shapes while keeping their single crystalline nature. Here, using the cell wall of the dinoflagellate L. granifera as a model, sustainably harvested biogenic calcite is successfully transformed into nano-structured perovskites. Three variants of lead halide perovskites CH3NH3PbX3 are generated with X = Cl−, Br− and I−; exhibiting emission peak-wavelength ranging from blue, to green, to near-infrared, respectively. The approach can be used for the mass production of nano-architectured perovskites with desired morphological, textural and, consequently, physical properties exploiting the numerous templates provided by calcite forming unicellular organisms.

Keywords: Perovskite; Algae; Crystallographic properties; Textures; Mass production

Permalink: https://www.hzdr.de/publications/Publ-36893
Publ.-Id: 36893


Passive SOBP generation from a static proton pencil beam using 3D-printed range modulators for FLASH experiments

Horst, F. E.; Beyreuther, E.; Bodenstein, E.; Gantz, S.; Misseroni, D.; Pugno, N.; Schuy, C.; Tommasino, F.; Weber, U.; Pawelke, J.

The University Proton Therapy facility in Dresden (UPTD), Germany, is equipped with an experimental room with a beamline providing a static pencil beam. High proton beam currents can be achieved at this beamline which makes it suitable for FLASH experiments. However, the established experimental setup uses only the entrance channel of the proton Bragg curve. In this work, a set of 3D-printed range modulators designed to generate spread out Bragg peaks (SOBPs) for radiobiological experiments at ultra-high dose rate at this beamline is described. A new method to optimize range modulators specifically for the case of a static pencil beam based on the central depth dose profile is introduced. Modulators for two different irradiation setups were produced and characterized experimentally by measurements of lateral and depth dose distributions using different detectors. In addition, Monte Carlo simulations were performed to assess profiles of the dose averaged linear energy transfer. These newly produced range modulators will allow future proton FLASH experiments in the SOBP at UPTD with two different experimental setups.

Keywords: proton therapy; range modulator; 3D-printing; spread out Bragg peak; FLASH effect; ultra-high dose rate

Permalink: https://www.hzdr.de/publications/Publ-36892
Publ.-Id: 36892


Transferable Interatomic Potentials for Aluminum from Ambient Conditions to Warm Dense Matter

Kumar, S.; Tahmasbi, H.; Ramakrishna, K.; Lokamani, M.; Nikolov, S.; Tranchida, J.; Wood, M. A.; Cangi, A.

We present a study on the transport and materials properties of aluminum spanning from ambient to warm dense matter conditions using a machine-learned interatomic potential (ML-IAP). Prior research has utilized ML-IAPs to simulate phenomena in warm dense matter, but these potentials have often been calibrated for a narrow range of temperature and pressures. In contrast, we train a single ML-IAP over a wide range of temperatures, using density functional theory molecular dynamics (DFT-MD) data. Our approach overcomes computational limitations of DFT-MD simulations, enabling us to study transport and materials properties of matter at higher temperatures and longer
time scales. We demonstrate the ML-IAP transferability across a wide range of temperatures using molecular-dynamics (MD) by examining the thermal conductivity, diffusion coefficient, viscosity, sound velocity, and ion-ion structure factor of aluminum up to about 60,000 K, where we find good agreement with previous theoretical data.

Keywords: Warm Dense Matter; Machine-Learned Interatomic Potential; Transport Coefficients; Molecular Dynamics; Materials Properties; Ion-Ion Structure Factor

Related publications

Permalink: https://www.hzdr.de/publications/Publ-36890
Publ.-Id: 36890


Nonreciprocal Phonon Propagation in a Metallic Chiral Magnet

Nomura, T.; Zhang, X.-X.; Takagi, R.; Karube, K.; Kikkawa, A.; Taguchi, Y.; Tokura, Y.; Zherlitsyn, S.; Kohama, Y.; Seki, S.

The phonon magnetochiral effect (MChE) is the nonreciprocal acoustic and thermal transports of phonons caused by the simultaneous breaking of the mirror and time-reversal symmetries. So far, the phonon MChE has been observed only in a ferrimagnetic insulator Cu2OSeO3, where the nonreciprocal response disappears above the Curie temperature of 58 K. Here, we study the nonreciprocal acoustic properties of a room-temperature ferromagnet Co9Zn9Mn2 for unveiling the phonon MChE close to room temperature. Surprisingly, the nonreciprocity in this metallic compound is enhanced at higher temperatures and observed up to 250 K. This clear contrast between insulating Cu2OSeO3 and metallic Co9Zn9Mn2 suggests that metallic magnets have a mechanism to enhance the nonreciprocity at higher temperatures. From the ultrasound and microwave-spectroscopy experiments, we conclude that the magnitude of the phonon MChE of Co9Zn9Mn2 mostly depends on the Gilbert damping, which increases at low temperatures and hinders the magnon-phonon hybridization. Our results suggest that the phonon nonreciprocity could be further enhanced by engineering the magnon band of materials.

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36889
Publ.-Id: 36889


Geschmolzenes Spineis

Wosnitza, J.

In magnetischen Materialien „frieren“ die magnetischen Momente üblicherweise in wohlgeordneten oder glasartigen Strukturen ein. Quanteneffekte können dazu führen, dass diese Strukturen „schmelzen“ und die Spinflüssigkeit selbst am absoluten Nullpunkt nicht ordnet.

Permalink: https://www.hzdr.de/publications/Publ-36888
Publ.-Id: 36888


Data publication: Morphological transitions in the patterning of the crystalline Ge(001) surface induced by ion irradiation

Erb, D.; Pearson, D. A.; Skeren, T.; Engler, M.; Bradley, R. M.; Facsko, S.

Rohdaten Rasterkraftmikroskopie

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36887
Publ.-Id: 36887


An intermediate morphology in the patterning of the crystalline Ge(001) surface induced by ion irradiation

Erb, D.; Pearson, D. A.; Skeren, T.; Engler, M.; Bradley, R. M.; Facsko, S.

We investigate the morphologies of the Ge(001) surface that are produced by bombardment with a normally incident, broad argon ion beam at sample temperatures above the recrystallization temperature. Two previously-observed kinds of topographies are seen, i.e., patterns consisting of upright and inverted rectangular pyramids, as well as patterns composed of shallow, isotropic basins. In addition, we observe the formation of an unexpected third type of pattern for intermediate values of the temperature, ion energy and ion flux. In this type of intermediate morphology, isolated peaks with rectangular cross sections stand above a landscape of shallow, rounded basins. We also extend past theoretical work to include a second order correction term that comes from the curvature dependence of the sputter yield. For a range of parameter values, the resulting continuum model of the surface dynamics produces patterns that are remarkably similar to the intermediate morphologies we observe in our experiments. The formation of the isolated peaks is the result of a term that is not ordinarily included in the equation of motion, a second order correction to the curvature dependence of the sputter yield.

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36885
Publ.-Id: 36885


Data publication: Non-empirical mixing coefficient for hybrid XC functionals from analysis of the XC kernel

Moldabekov, Z.; Lokamani, M.; Vorberger, J.; Cangi, A.; Dornheim, T.

The density values from KS-DFT simulations presented in the paper by Moldabekov et al., J. Phys. Chem. Lett. 2023, 14, 5, 1326–1333

Keywords: warm dense matter; hybrid functionals; Hartree-Fock

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36884
Publ.-Id: 36884


Ultrafast Tunable Terahertz-to-Visible Light Conversion through Thermal Radiation from Graphene Metamaterials

Ilyakov, I.; Ponomaryov, O.; Saleta Reig, D.; Murphy, C.; Dudley Mehew, J.; de Oliveira, T.; Prajapati, G. L.; Arshad, A.; Deinert, J.-C.; Felicia Craciun, M.; Russo, S.; Kovalev, S.; Tielrooij, K.-J.

Several technologies, including photodetection, imaging and data communication, could greatly benefit from the availability of fast and controllable conversion of terahertz (THz) light to visible light. Here, we demonstrate that the exceptional properties and dynamics of electronic heat in graphene allow for THz-to-visible conversion, which is switchable at a sub-nanosecond timescale. We show a tunable on/off ratio of more than 30 for the emitted visible light, achieved through electrical gating using a gate voltage on the order of one Volt. We also demonstrate that a grating-graphene metamaterial leads to an increase in THz-induced emitted power in the visible range by two orders of magnitude. The experimental results are in agreement with a thermodynamic model that describes black-body radiation from the electron system heated through intraband Drude absorption of THz light. These results provide a promising route towards novel functionalities of optoelectronic technologies in the THz regime.

Keywords: Terahertz radiation; frequency conversion; ultrafast thermal emission; graphene; electrical gating; metamaterial

Permalink: https://www.hzdr.de/publications/Publ-36882
Publ.-Id: 36882


Dual Mode Strain–Temperature Sensor with High Stimuli Discriminability and Resolution for Smart Wearables

Xiao, H.; Li, S.; He, Z.; Wu, Y.; Gao, Z.; Hu, C.; Hu, S.; Wang, S.; Liu, C.; Shang, J.; Liao, M.; Makarov, D.; Liu, Y.; Li, R.-W.

Strain and temperature are important physiological parameters for health monitoring, providing access to the respiration state, movement of joints and inflammation processes. The challenge for smart wearables is to unambiguously discriminate strain and temperature using a single sensor element assuring a high degree of sensor integration. Here, we report a dual-modal sensor with two electrodes and tubular mechanically heterogeneous structure enabling simultaneous sensing of strain and temperature without cross-talk. The sensor structure consists of a thermocouple coiled around an elastic strain-to-magnetic induction conversion unit, revealing a giant magnetoelastic effect, and accommodating a magnetic amorphous wire. The thermocouple provides access to temperature and its coil structure allows to measure impedance changes caused by the applied strain. The dual-modal sensor also exhibits interference-free temperature sensing performance with high coefficient of 54.49 μV/°C, low strain and temperature detection limits of 0.1% and 0.1 °C, respectively. We demonstrate the use of these sensors in smart textiles to monitor continuously breathing, body movement, body temperature and ambient temperature. The developed multifunctional wearable sensor is needed for applications in early disease prevention, health monitoring and interactive electronics as well as for smart prosthetics and intelligent soft robotics.

Keywords: smart wearables; dual sensing

Permalink: https://www.hzdr.de/publications/Publ-36881
Publ.-Id: 36881


Structural analyses of heavy-ion irradiated monazites

Huittinen, N. M.; Gilson, S.; Bukaemskiy, A.; Murphy, G. L.; Marquardt, J.; Lender, T.; Lippold, H.; Svitlyk, V.; Nießen, J.; Hennig, C.; Richter, S.; Akhmadaliev, S.; Poonoosamy, J.; Trautmann, C.

Monazites are rare earth phosphates that are potential host matrices for the immobilization of actinides in high-level radioactive waste streams. This is due to their ability to incorporate various cations through different substitution mechanisms as well as their radiation resistance as observed in natural monazite mineral samples. In this study, LnPO4 monazite ceramics and single crystals doped with 500 ppm EuIII as a luminescent probe were irradiated with heavy ions to simulate the recoil of daughter products that occurs during alpha decay of the actinides. More specifically, irradiation experiments were conducted either with 14 MeV Au ions at fluences ranging from 5×1013 – 1×1015 ions/cm2 or with swift 1.7 GeV Au ions at fluences of 5×1011 – 2×1012 ions/cm2.
Irradiated monazite ceramics were analyzed with electron microscopy (SEM), vertical scanning interferometry (VSI), grazing incidence diffraction (GID), Raman spectroscopy, and luminescence spectroscopy to probe long and short range order of the monazite microstructure.
SEM micrographs and VSI data show clear damage of the irradiated regions of the ceramics, in the form of swollen grains and grain boundaries. GID images and powder patterns reveal diffuse scattering and amorphous contributions in irradiated samples. Solid solution compositions show larger damage than corresponding monazite endmembers, while polycrystalline and single crystal samples show similar level of amorphization. In the local coordination environments, Raman spectra of irradiated samples display a shoulder on the ν1 peak, indicating disruption in the vibrational modes of the phosphate tetrahedra. Confocal measurements of the swift heavy-ion irradiated monazites show full amorphization of the surface layers of the monazites samples, and increasing crystallinity with increasing sample depth. Luminescence data illustrate differences in the local LnO9 polyhedral environment in the monazites with irradiation. Integrated excitation spectra show a difference in the intensity and position of the excitation peak with irradiation. Especially single crystal data show a systematic decrease of the local site symmetry of the Eu3+ cation, and a general broadening of emission spectra, indicative for reduced local order following amorphization.

Related publications

  • Lecture (Conference)
    47th Scientific Basis for Nuclear Waste Management (SBNWM), 06.-10.11.2023, Cologne, Germany

Permalink: https://www.hzdr.de/publications/Publ-36880
Publ.-Id: 36880


Fundamental investigations of actinide immobilization by incorporation into solid phases relevant for final disposal

Huittinen, N. M.; Braga Ferreira Dos Santos, L.; Gilson, S.; Hennig, C.; Lender, T.; Marquardt, J.; Murphy, G. L.; Nießen, J.; Peters, L.; Richter, S.; Svitlyk, V.; Tonnesen, T.; Winkler, B.

This contribution provides an overview of a current research network funded by the German Federal Ministry of Education and Research (BMBF), entitled “Fundamental investigations of actinide immobilization by incorporation into solid phases relevant for final disposal” – AcE. The AcE project aims at understanding the incorporation and immobilization of actinides (An) in crystalline, repository-relevant solid phases, such as zirconia (ZrO2) and UO2, but also in zircon (ZrSiO4), pyrochlores (Ln2Zr2O7) and orthophosphates of the monazite type (LnPO4), which may find use as host matrices for the immobilization and safe disposal of high-level waste streams.
Recent studies by the AcE-project consortium, addressing the structure, properties, and the radiation tolerance of monazites and Zr(IV)-based solid phases containing actinides or their surrogates from the lanthanide series will be presented. Material synthesis strategies in the AcE project have aimed at generating single-phase solid solutions in the form of polycrystalline powders, dense ceramics, and single crystals. Structural studies using powder X-ray diffraction at ambient conditions, but also at high temperatures and pressures have been complemented with a wide range of microscopic and spectroscopic techniques to address differences between the host- and dopant environments in the solid matrices at ambient and extreme conditions. The radiation tolerance of the synthetic solid phases have been investigated by combining external heavy-ion irradiation of inactive Ln-doped materials and in situ self-irradiation of 241Am-doped Zr(IV)-phases with monoclinic, cubic defect fluorite and pyrochlore structures. The latter experiments have been conducted in joint efforts with the Joint Research Center in Karlsruhe within the ActUsLab programme.

Related publications

  • Poster
    47th Scientific Basis for Nuclear Waste Management (SBNWM), 06.-10.11.2023, Cologne, Germany

Permalink: https://www.hzdr.de/publications/Publ-36879
Publ.-Id: 36879


Investigations towards incorporation of Eu3+ and Cm3+ during ZrO2 crystallization in aqueous solution

Opitz, L.; Hübner, R.; Shams Aldin Azzam, S.; Gilson, S.; Finkeldei, S. C.; Huittinen, N. M.

Nuclear energy provides a widely applied carbon-reduced energy source. Following operation, the spent nuclear fuel (SNF), containing a mixture of radiotoxic elements such as transuranics, needs to be safely disposed of. Safe storage of SNF in a deep geological repository (DGR) relies on multiple engineered and natural retention barriers to prevent environmental contamination. In this context, zirconia (ZrO2) formed on the SNF rod cladding, could be employed as an engineered barrier for immobilization of radionuclides via structural incorporation. This study investigates the incorporation of Eu3+ and Cm3+, representatives for trivalent transuranics, into zirconia by co-precipitation and crystallization in aqueous solution at 80 °C. Complementary structural and microstructural characterization has been carried out by Powder X-ray Diffraction (PXRD), spectrum imaging analysis based on Energy-Dispersive X-ray Spectroscopy in Scanning Transmission Electron Microscopy mode (STEM-EDXS), and luminescence spectroscopy. The results reveal the association of the dopants with the zirconia particles and elucidate the presence of distinct bulk and superficially incorporated species. Hydrothermal aging for up to 460 days in alkaline media points to great stability of these incorporated species after initial crystallization, with no indication of phase segregation or release of Eu3+ and Cm3+ over time. These results suggest that zirconia would be a suitable technical retention barrier for mobilized trivalent actinides in a DGR.

Keywords: nuclear waste management; crystallization; zirconia; incorporation; trivalent; luminescence spectroscopy; transmission electron microscopy; X-ray diffraction

Related publications

Permalink: https://www.hzdr.de/publications/Publ-36878
Publ.-Id: 36878


Structure and radiation tolerance of crystalline ceramics. The RISE-project: 241Am-doped zirconates

Huittinen, N. M.; Gilson, S.; Murphy, G.; Richter, S.; Popa, K.; Valu, O.; Colle, J.-Y.; Walter, O.

Spent nuclear fuel (SNF) from nuclear reactors operating worldwide will be disposed of directly or after reprocessing. In the latter case, generation of specific waste streams, e.g. minor actinide-containing waste, may require immobilization in durable, crystalline waste forms. Such candidate phases for the immobilization of (minor) actinides are various Zr(IV)-bearing solid phases like pyrochlore and zirconia. In addition to their use as potential ceramic waste matrices or inert matrix fuels for e.g. the incineration of waste plutonium, Zr-bearing phases, especially ZrO2, may be of importance as corrosion products in the dissolution of Zircaloy cladding material of SNF rods. ZrO2 is monoclinic phase (P21/c) at ambient conditions, and transforms into tetragonal (P4_2/nmc) and cubic phases (Fm3 ̅m) at high temperatures of around 1200 °C and 2370 °C, respectively. However, particle size effects, the incorporation of foreign ions such as the actinides, as well as high radiation fields are also known to influence the stability fields of the polymorphs.
This contribution provides an overview of recent studies addressing the structure, properties and the radiation tolerance of Zr(IV)-based solid phases containing actinides and their surrogates from the lanthanide series. Synthesis strategies and structural transformations taking place as a result of An(IV) or Ln(IV) incorporation in ZrO2 will be presented. Combining bulk structural characterization using powder X-ray diffraction (PXRD) with spectroscopic investigations, differences between the host- and dopant environments can be explored. In addition, radiation damage studies combining external heavy-ion irradiation of inactive Ln-doped materials and in situ self-irradiation of recently synthesized 241Am-doped Zr(IV)-phases with monoclinic, cubic defect fluorite and pyrochlore structures, will be addressed.

  • Poster
    18th international conference on the chemistry and migration behaviour of actinides and fission products in the geosphere, 24.-29.09.2023, Nantes, France

Permalink: https://www.hzdr.de/publications/Publ-36877
Publ.-Id: 36877


Novel Identifier of Transitions in Bubble Columns Operated with Water and Aqueous Alcohol Solutions

Nedeltchev, S. N.; Marchini, S.; Schubert, M.; Hlawitschka, M. W.; Hampel, U.

The accurate identification of the transition velocities Utrans in bubble columns (BCs) is very important for their effective design, operation and scale-up. In this work, a novel parameter (new hybrid index (NHI)) has been developed and successfully applied to gas holdup and pressure fluctuations recorded in various BCs operated with water and aqueous solutions of alcohols (ethanol and iso-propanol).
The first Utrans has been identified on the basis of a well-pronounced local NHI minimum, whereas the second Utrans has been distinguished by the point, from which the NHI profile levels off. It has been concluded that the main Utrans depend on the type of gas-liquid system and sparger used. A set of several Utrans has been reported.

Keywords: Bubble columns; New hybrid index; Gas holdup fluctuations; Pressure fluctuations; Main transition velocities

Downloads

  • Secondary publication expected from 11.07.2024

Permalink: https://www.hzdr.de/publications/Publ-36876
Publ.-Id: 36876


Vibrational spectroscopy of Cu+(H2)4: about anharmonicity and fluxionality

Jin, J.; Wulf, T.; Jorewitz, M.; Heine, T.; Asmis, K. R.

The vibrational spectra of the copper(i) cation-dihydrogen complexes Cu+(H2)4, Cu+(D2)4 and Cu+(D2)3H2 are studied using cryogenic ion trap vibrational spectroscopy in combination with quantum chemical calculations. The infrared photodissociation (IRPD) spectra (2500-7300 cm−1) are assigned based on a comparison to IR spectra calculated using vibrational second-order perturbation theory (VPT2). The IRPD spectra exhibit ≈60 cm−1 broad bands that lack rotational resolution, indicative of rather floppy complexes even at an ion trap temperature of 10 K. The observed vibrational features are assigned to the excitations of dihydrogen stretching fundamentals, combination bands of these fundamentals with low energy excitations as well as overtone excitations of a minimum-energy structure with Cs symmetry. The three distinct dihydrogen positions present in the structure can interconvert via pseudorotations with energy barriers less than 10 cm−1, far below the zero-point vibrational energy. Ab initio Born-Oppenheimer molecular dynamics (BOMD) simulations confirm the fluxional behavior of these complexes and yield an upper limit for the timeframe of the pseudorotation on the order of 10 ps. For Cu+(D2)3H2, the H2 and D2 loss channels yield different IRPD spectra indicating non-ergodic behavior. © 2023 The Royal Society of Chemistry.

Keywords: Copper compounds; Molecular dynamics; Perturbation techniques; Vibrational spectroscopy; Anharmonicities; Dihydrogen; Dihydrogen complexes; Fluxionality; Infrared photodissociation; Ion traps; Pseudorotation; Quantum chemical calculations; Quantum-chemical calculation; Spectra's; Quantum chemistry

Permalink: https://www.hzdr.de/publications/Publ-36875
Publ.-Id: 36875


STereotactic Arrhythmia Radioablation (STAR): the Standardized Treatment and Outcome Platform for Stereotactic Therapy Of Re-entrant tachycardia by a Multidisciplinary consortium (STOPSTORM.eu) and review of current patterns of STAR practice in Europe

Grehn, M.; Mandija, S.; Miszczyk, M.; Krug, D.; Tomasik, B.; Stickney, K. E.; Alcantara, P.; Alongi, F.; Anselmino, M.; Aranda, R. S.; Balgobind, B. V.; Boda-Heggemann, J.; Boldt, L.-H.; Bottoni, N.; Cvek, J.; Elicin, O.; de Ferrari, G. M.; Hassink, R. J.; Hazelaar, C.; Hindricks, G.; Hurkmans, C.; Iotti, C.; Jadczyk, T.; Jiravsky, O.; Jumeau, R.; Kristiansen, S. B.; Levis, M.; López, M. A.; Martí-Almor, J.; Mehrhof, F.; Møller, D. S.; Molon, G.; Ouss, A.; Peichl, P.; Plasek, J.; Postema, P. G.; Quesada, A.; Reichlin, T.; Rordorf, R.; Rudic, B.; Saguner, A. M.; Ter, B.; Rachel, M. A.; Torrecilla, J. L.; Troost, E. G. C.; Vitolo, V.; Andratschke, N.; Zeppenfeld, K.; Blamek, S.; Fast, M.; de Panfilis, L.; Blanck, O.; Pruvot, E.; Verhoeff, J. J. C.

The EU Horizon 2020 Framework-funded Standardized Treatment and Outcome Platform for Stereotactic Therapy Of Re-entrant tachycardia by a Multidisciplinary (STOPSTORM) consortium has been established as a large research network for investigating STereotactic Arrhythmia Radioablation (STAR) for ventricular tachycardia (VT). The aim is to provide a pooled treatment database to evaluate patterns of practice and outcomes of STAR and finally to harmonize STAR within Europe. The consortium comprises 31 clinical and research institutions. The project is divided into nine work packages (WPs): (i) observational cohort; (ii) standardization and harmonization of target delineation; (iii) harmonized prospective cohort; (iv) quality assurance (QA); (v) analysis and evaluation; (vi, ix) ethics and regulations; and (vii, viii) project coordination and dissemination. To provide a review of current clinical STAR practice in Europe, a comprehensive questionnaire was performed at project start. The STOPSTORM Institutions' experience in VT catheter ablation (83% ≥ 20 ann.) and stereotactic body radiotherapy (59% > 200 ann.) was adequate, and 84 STAR treatments were performed until project launch, while 8/22 centres already recruited VT patients in national clinical trials. The majority currently base their target definition on mapping during VT (96%) and/or pace mapping (75%), reduced voltage areas (63%), or late ventricular potentials (75%) during sinus rhythm. The majority currently apply a single-fraction dose of 25 Gy while planning techniques and dose prescription methods vary greatly. The current clinical STAR practice in the STOPSTORM consortium highlights potential areas of optimization and harmonization for substrate mapping, target delineation, motion management, dosimetry, and QA, which will be addressed in the various WPs. © The Author(s) 2023. Published by Oxford University Press on behalf of the European Society of Cardiology.

Keywords: Cardiac arrhythmias; Consortium; EU Horizon 2020; Stereotactic arrhythmia radioablation; Stereotactic body radiotherapy; Ventricular tachycardia

Permalink: https://www.hzdr.de/publications/Publ-36874
Publ.-Id: 36874


Semiconducting Conjugated Coordination Polymer with High Charge Mobility Enabled by “4 + 2” Phenyl Ligands

Huang, X.; Fu, S.; Lin, C.; Lu, Y.; Wang, M.; Zhang, P.; Huang, C.; Li, Z.; Liao, Z.; Zou, Y.; Li, J.; Zhou, S.; Helm, M.; Petkov, P. S.; Heine, T.; Bonn, M.; Wang, H. I.; Feng, X.; Dong, R.

Electrically conductive coordination polymers and metal–organic frameworks are attractive emerging electroactive materials for (opto-)electronics. However, developing semiconducting coordination polymers with high charge carrier mobility for devices remains a major challenge, urgently requiring the rational design of ligands and topological networks with desired electronic structures. Herein, we demonstrate a strategy for synthesizing high-mobility semiconducting conjugated coordination polymers (c-CPs) utilizing novel conjugated ligands with D2h symmetry, namely, “4 + 2” phenyl ligands. Compared with the conventional phenyl ligands with C6h symmetry, the reduced symmetry of the “4 + 2” ligands leads to anisotropic coordination in the formation of c-CPs. Consequently, we successfully achieve a single-crystalline three-dimensional (3D) c-CP Cu4DHTTB (DHTTB = 2,5-dihydroxy-1,3,4,6-tetrathiolbenzene), containing orthogonal ribbon-like π–d conjugated chains rather than 2D conjugated layers. DFT calculation suggests that the resulting Cu4DHTTB exhibits a small band gap (∼0.2 eV), strongly dispersive energy bands near the Fermi level with a low electron-hole reduced effective mass (∼0.2m0*). Furthermore, the four-probe method reveals a semiconducting behavior with a decent conductivity of 0.2 S/cm. Thermopower measurement suggests that it is a p-type semiconductor. Ultrafast terahertz photoconductivity measurements confirm Cu4DHTTB’s semiconducting nature and demonstrate the Drude-type transport with high charge carrier mobilities up to 88 ± 15 cm2 V–1 s–1, outperforming the conductive 3D coordination polymers reported till date. This molecular design strategy for constructing high-mobility semiconducting c-CPs lays the foundation for achieving high-performance c-CP-based (opto-)electronics.

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36873
Publ.-Id: 36873


A tailored 100%-efficient 532/1064-nm demultiplexer in y-cut LiNbO3 crystal

Liu, H.; Li, Y.; Yang, Q.; Zhou, S.; Jia, Y.

In this Letter, we report a tailored 532/1064-nm demultiplexer based on a multimode interference (MMI) coupler with an efficiency of 100%. The device structure is designed according to the self-imaging principle, and the propagation and the wavelength division performance are simulated by the beam propagation method. The demultiplexer is fabricated in a y-cut LiNbO3 crystal by femtosecond laser direct writing (FLDW) combined with the ion implantation technique. The end-face coupling system is used to measure the near field intensity distribution, and the spectra collected from the output ports are obtained by spectrometers. The simulated and the experimental results indicate that the customized demultiplexer in the LiNbO3 crystal presents excellent wavelength division performance operating at 532 nm and 1064 nm. This work demonstrates the application potential of FLDW technology for developing miniaturized photonic components and provides a new strategy for fabricating high-efficiency integrated wavelength division devices on an optical monocrystalline platform.

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36872
Publ.-Id: 36872


Photo-response of the N = Z nucleus 24Mg

Deary, J.; Scheck, M.; Schwengner, R.; Odonnell, D.; Bemmerer, D.; Beyer, R.; Hensel, T.; Junghans, A. R.; Kögler, T.; Müller, S. E.; Römer, K.; Schmidt, K.; Turkat, S.; Urlaß, S.; Wagner, A.; Bowry, M.; Adsley, P.; Agar, O.; Chapman, R.; Crespi, F. C. L.; Doherty, D. T.; Friman-Gayer, U.; Herzberg, R.-D.; Isaak, J.; Janssens, R. V. F.; Kröll, T.; Löher, B.; Nara-Singh, B. S.; von Neumann-Cosel, P.; Pellegri, L.; Peters, E. E.; Rainovski, G.; Savran, D.; Smith, J. F.; Spieker, M.; Thirolf, P. G.; Triambak, S.; Tornow, W.; Venhart, M.; Wiedeking, M.; Wieland, O.; Yates, S. W.; Zilges, A.

The electric E1 and magnetic M 1 dipole responses of the N = Z nucleus 24 Mg were investigated in an inelastic photon scattering experiment. The 13.0 MeV electrons, which were used to produce the unpolarised bremsstrahlung in the entrance channel of the 24 Mg(γγ) reaction, were delivered by the ELBE accelerator of the Helmholtz-Zentrum Dresden-Rossendorf. The collimated bremsstrahlung photons excited one J = 1-, four J = 1+ , and six J = 2+ states in 24 Mg. De-excitation γ rays were detected using the four high-purity germanium detectors of the γELBE setup, which is dedicated to nuclear resonance fluorescence experiments. In the energy region up to 13.0 MeV a total B(M1)up = 2.7(3) µN 2 is observed, but this N = Z nucleus exhibits only marginal E1 strength of less than B(E1)up = 0.61 10-3 e2 fm2 . The B(M1, 1+ -> 2+1 )/B(M1, 1+ -> 0gs ) branching ratios in combination with the expected results from the Alaga rules demonstrate that K is a good approximative quantum number for 24Mg. The use of the known (E0, 0+_2 -> 0+_gs) strength and the measured B(M1, 1+ -> 0+_2) / B(M1, 1+ -> 0+_ gs) branching ratio of the 10.712 MeV 1+ level allows, in a two-state mixing model, an extraction of the between the prolate ground-state structure and shape-coexisting superdeformed structure built upon the 6432-keV 0+_2 level.

Keywords: Nuclear resonance fluorescence; photon scattering; bremsstrahlung; superconducting electron accelerator; electric and magnetic dipole strengths

Related publications

Permalink: https://www.hzdr.de/publications/Publ-36871
Publ.-Id: 36871


Prediction of a roton-type feature in warm dense hydrogen

Hamann, P.; Kordts, L.; Filinov, A.; Bonitz, M.; Dornheim, T.; Vorberger, J.

In a recent Letter [T. Dornheim \textit{et al.}, Phys. Rev. Lett. \textbf{121}, 255001 (2018)], it was predicted on the basis of \textit{ab initio} quantum Monte Carlo simulations that, in a uniform electron gas, the peak $\omega_0$ of the dynamic structure factor $S(q,\omega)$ exhibits an unusual non-monotonic wave number dependence, where $d\omega_0/dq < 0$, at intermediate $q$, under strong coupling conditions. This effect was subsequently explained by the pair alignment of electrons [T. Dornheim \textit{et al.}, Comm. Phys. \textbf{5}, 304 (2022)].
Here we predict that this non-monotonic dispersion resembling the roton-type behavior known from superfluids should be observable in a dense, partially ionized hydrogen plasma. Based on a combination of path integral Monte Carlo simulations and linear response results for the density response function, we present the approximate range of densities, temperatures and wave numbers and make predictions for possible experimental observations.

Keywords: roton; hydrogen; dynamic structure; x-ray scattering

Permalink: https://www.hzdr.de/publications/Publ-36870
Publ.-Id: 36870


Core Damage Extent Analysis of Large-Break LOCA for 4-Loop Pressurized Water Reactor with Detailed 3D Model of Reactor Pressure Vessel and Core

Jobst, M.; Diaz Pescador, E.; Kliem, S.

According to German requirements for LOCA analyses, it has to be proven in addition to the common safety criteria that less than 10% of the fuel rods rupture during the accident. In order to perform such core damage extent analysis, a newly developed model of a generic German Pressurized Water Reactor is presented. The model developed with the system code ATHLET-CD includes four loops and a detailed configuration of the reactor pressure vessel. A 3D parallel channel approach is applied for the downcomer, lower and upper plenum and the core, which is modelled by 193 thermal-hydraulic channels (one channel per fuel assembly) and multiple rods per channel in order to represent the power distribution in a sufficiently accurate way. New for such detailed system code analyses is that the deformation and burst of the fuel rods and the feedback to thermal hydraulics by reduction of the flow cross-sections is taken into account. The number of failed rods has been determined for best-estimate and top-peaked power profiles and has been compared to the 10% criterion. Furthermore, the large-break LOCA leads to asymmetric thermal-hydraulic boundary conditions at the RPV inlets and outlets because of break of only 1 out of 4 loops, asymmetric emergency core-cooling due to postulated outage and/or malfunction of certain trains and the influ-ence of the pressurizer. In contrast to previous studies, an asymmetric distribution of the failed rods within the core is observed, depending on the location of break, pressurizer and available ECCS injection.

Keywords: PWR; LOCA; Core Damage Extent Analysis; System Code Development

  • Contribution to proceedings
    20th International Topical Meeting on Nuclear Reactor Thermal Hydraulics (NURETH-20), 20.-25.08.2023, Washington D.C., USA
    20th International Topical Meeting on Nuclear Reactor Thermal Hydraulics (NURETH-20), 572-585
    DOI: 10.13182/NURETH20-40856
  • Lecture (Conference)
    20th International Topical Meeting on Nuclear Reactor Thermal Hydraulics (NURETH-20), 20.-25.08.2023, Washington D.C., USA

Permalink: https://www.hzdr.de/publications/Publ-36868
Publ.-Id: 36868


Exploring the lowest levels of environmental 90Sr/Sr compared to 236U/U in carbonates and seawater using a new, highly sensitive Accelerator Mass Spectrometry technique

Winkler, S.; Martschini, M.; Merchel, S.; Carilli, J.; Zinke, J.; Steier, P.; Batsankalashvili, T.; Henderson, G. M.; Golser, R.

Strontium-90 (90Sr) is an anthropogenic radionuclide, which, due to its radiological relevance, has been most intensively monitored in the past. In terms of initial activity, over 630 PBb of this radioisotope have been distributed globally from stratospheric fallout of bomb-testing, and there are more localized contributions from test, accidents, and releases from reprocessing plants. In the past massive sample sizes (up to 100 l of seawater or 100 g of coral aragonite) were required even right after the peak period of global fall-out from bomb testing. On the other hand, the high amount of strontium dissolved in seawater complicates the use of mass spectrometric methods, as an isotopic abundance sensitivity of at least 1·10-15 is required to detect the estimated main signal. With recent advances in isobar separation technique in accelerator mass spectrometry (AMS) at the University of Vienna, this requirement has come within reach, offering new research possibilities. The new technique uses an ion-cooler and laser-photo-detachment to suppress the stable isobar 90Zr almost completely. With initial test samples we could confirm an isotopic abundance sensitivity of 8·10-16 90Sr/Sr, sufficient for application to ocean water samples. In this presentation we will show comparison of 90Sr to 236U, another ocean tracer that has been studied intensively recently. We will present results from contemporary coral skeleton material, the methods, requirements, and impact of sample preparation. Further, first result from ocean water samples and the sample preparation and blank levels for these types of samples will be shown. Finally, we explain our sample preparation scheme to extract 236U, simultaneously with 90Sr for multi-isotope applications of both.

Keywords: marine radioactivity; ocean tracers; 90-Sr; 236-U; GEOTRACES

Related publications

  • Lecture (Conference)
    ENVIRA 2023 - 7th International Conference on Environmental Radioactivity, 17.-22.09.2023, Sevilla, Espana

Permalink: https://www.hzdr.de/publications/Publ-36866
Publ.-Id: 36866


Deep anoxic aquifers could act as sinks for uranium through microbial-assisted mineral trapping

Pidchenko, I. N.; Christensen, J. N.; Kutzschbach, M.; Ignatyev, K.; Puigdomenech, I.; Tullborg, E.-L.; Roberts, N. M. W.; Troy Rasbury, E.; Northrup, P.; Tappero, R.; Kvashnina, K.; Schäfer, T.; Suzuki, Y.; Drake, H.

Uptake of uranium (U) by secondary minerals, such as carbonates and iron (Fe)-sulfides, that
occur ubiquitously on Earth, may be substantial in deep anoxic environments compared to
surficial settings due to different environment-specific conditions. Yet, knowledge of U
reductive removal pathways and related fractionation between 238 U and 235 U isotopes in
deep anoxic groundwater systems remain elusive. Here we show bacteria-driven degradation
of organic constituents that influences formation of sulfidic species facilitating reduction of
geochemically mobile U(VI) with subsequent trapping of U(IV) by calcite and Fe-sulfides.
The isotopic signatures recorded for U and Ca in fracture water and calcite samples provide
additional insights on U(VI) reduction behaviour and calcite growth rate. The removal effi-
ciency of U from groundwater reaching 75% in borehole sections in fractured granite, and
selective U accumulation in secondary minerals in exceedingly U-deficient groundwater
shows the potential of these widespread mineralogical sinks for U in deep anoxic
environments.

Related publications

Permalink: https://www.hzdr.de/publications/Publ-36865
Publ.-Id: 36865


Pressure evolution of electron dynamics in the superconducting kagome metal CsV₃Sb₅

Wenzel, M.; Tsirlin, A. A.; Capitani, F.; Chan, Y. T.; Ortiz, B. R.; Wilson, S. D.; Dressel, M.; Uykur, E.

The coexistence of the charge-density wave (CDW) and the superconducting phase and their tunability under external pressure remains one of the key focus points in understanding the electronic structure of AV3Sb5 (A = K, Rb, Cs) kagome metals. Here, we employ synchrotron-based infrared spectroscopy assisted by density-functional calculations to study the pressure evolution of the electronic structure at room temperature up to 17 GPa experimentally for the first time. The optical spectrum of CsV₃Sb₅ is characterized by the presence of localized carriers seen as a broad peak at finite frequencies in addition to the conventional metallic Drude response. The pressure dependence of this low-energy peak mirrors the re-entrant behavior of superconductivity and may be interpreted in terms of electron-phonon coupling changing with the growth and shrinkage of the Fermi surface (FS). Moreover, drastic modifications in the low-energy interband absorptions are observed upon the suppression of CDW. These changes are related to the upward shift of the Sb2 px +py band that eliminates part of the FS around the M-point, whereas band saddle points do not change significantly. These observations
shed new light on the mixed electronic and lattice origin of the CDW in CsV₃Sb₅.

Keywords: High pressure; Broadband infrared spectroscopy; Density functional theory; Charge density wave

Related publications

Permalink: https://www.hzdr.de/publications/Publ-36864
Publ.-Id: 36864


Strain-gradient-driven and magnetoelectric operation with order parameters in Cr2O3

Pylypovskyi, O.

Progress in computing technologies enforces an active search for novel materials, assuring low-power and high-speed operations. One of prospective materials for such needs is Cr2O3. Here, we discuss access to the order parameters and properties of antiferromagnetic domain walls related to the possibility of electric operations on them, as well as fundamental and technological perspectives of the recently accessed flexomagnetism in thin Cr2O3 films.

Keywords: antiferromagnetism; Cr2O3; flexoeffects; magnetoelectricity

  • Invited lecture (Conferences)
    META 2023, 18.-21.07.2023, Paris, France

Permalink: https://www.hzdr.de/publications/Publ-36863
Publ.-Id: 36863


Magnetic domains and flexomagnetism in Cr2O3

Pylypovskyi, O.

Antiferromagnets, which possess nearly zero magnetic moment and consist of a few magnetic sublattices connected by the symmetry operation of their permutation, represent a perspective material platform for technology and fundamental science. Among a variety of such materials, \ch{Cr2O3} is a unique example of the easy axis magnetoelectric material at room temperature. Here, we discuss measuring and manipulation of domain walls in single crystal and polycrystalline \ch{Cr2O3} samples, and respective applications including electric access to the texture state: pinning at grain boundaries, elastic degrees of freedom of a domain wall and detection of an uncompensated magnetization, which originates from the spatial distribution of the \neel{} temperature and is coupled with the strain gradient.

Keywords: antiferromagnetism; Cr2O3; domain walls; flexoeffects

  • Invited lecture (Conferences) (Online presentation)
    Intermag, 15.-19.05.2023, Sendai, Japan

Permalink: https://www.hzdr.de/publications/Publ-36862
Publ.-Id: 36862


Local and Nonlocal Effects of Geometry in Curvilinear Magnetic Nanoarchitectures

Pylypovskyi, O.

Interplay between the geometry and behavior of magnetic textures in statics and dynamics has been traditionally considered regarding planar confined samples and their boundaries (vortices in nanodisks, interaction of skyrmions and domain walls with notches etc.). Recent developments of experimental techniques on fabrication of freestanding 3D nanostructures gave a possibility to access and validate theoretical predictions of behavior of magnetic textures, related to the intrinsic geometric properties of extended films and complex sample topologies [1].

Properties of energy functionals in both, ferro- and antiferromagnetic samples reflect geometric symmetries in curvature-driven Dzyaloshinskii-Moriya interaction and anisotropies, which are proportional to the first and second powers of the curvatures, respectively [1]. Magnetostatics is also sensitive to the breaks of the geometric symmetries. In thin films, it is possible to tease out an interplay between the out-of-surface magnetization component and mean curvature of the film [2]. Furthermore, for such non-local textures as vortices hosted by asymmetric Py caps, it enables complex magnetochiral effects pronounced in twisting of the vortex string in a helix and coupling of this helix chirality with the vorticity of the whole texture [3].

Antiferromagnetic curvilinear nanoarchitectures provide more intrinsic material symmetries. In spin chains, the dipolar interaction provides the hard-axis shape anisotropy, with the anisotropy axis along the tangential direction to the chain. This makes the geometry-driven helimagnetic phase transition to be possible for any finite curvature and torsion of the chain [4]. The locally broken spatial translation symmetry of antiferromagnetic dimers in bipartite chains leads to the micromagnetic energy term of the non-chiral longitudinal Dzyaloshinskii energy symmetry and enables local weak ferromagnetic response related to the spatial inhomogeneity of the Neel vector [5]. The geometry-driven easy axis of anisotropy is present even if the material anisotropy is of the hard-axis type, which enables spin-flop transition governed by the chain shape. In a particular case of the ring with the hard-tangential anisotropy and uniform ground state, the helimagnetic phase transition appears in spin-flop phase and the intermediate canted phase for the case of strong Dzyaloshinskii-Moriya interaction [6].

References
1. D. Makarov, O. Volkov, A. Kakay et al., Adv. Mat. 34, 2101758 (2022)
2. D. Sheka, O. Pylypovskyi, P. Landeros et al., Commun. Phys. 3, 128 (2020)
3. O. Volkov, D. Wolf, O. Pylypovskyi, et al., Nat. Commun. In press (2023)
2. O. Pylypovskyi, D. Kononenko, K. Yershov et al., Nano Lett. 20, 8157 (2020)
5. O. Pylypovskyi, Y. Borysenko, J. Fassbender et al., Appl. Phys. Lett. 118, 182405 (2021)
6. Y. Borysenko, D. Sheka, J. Fassbender, et al., Phys. Rev. B 106, 174426 (2022)

Keywords: curvilinear ferromagnets; curvilinear antiferromagnets; nonlocal chiral effects

  • Invited lecture (Conferences)
    International Conference On Superconductivity and Magnetism - ICSM2023, 04.-11.05.2023, ölüdeniz-Fethiye, Turkey

Permalink: https://www.hzdr.de/publications/Publ-36861
Publ.-Id: 36861


Anisotropic effects in antiferromagnetic curvilinear spin chains

Pylypovskyi, O.; Borysenko, Y.; Kononenko, D. Y.; Yershov, K. V.; Roessler, U. K.; Tomilo, A.; van den Brink, J.; Faßbender, J.; Sheka, D. D.; Makarov, D.

Curvilinear spin chains are simplest antiferromagnetic systems revealing direct influence of their shape onto magnetic states via geometry-tracking anisotropies stemming from the dipolar interaction [1] or local surrounding [2]. Here, we show that in addition to the strongest effect onto magnetic state from exchange (biaxial anisotropy and chiral energy term) [1], the local break of the translational symmetry in curvilinear anisotropic antiferromagnets leads to (i) the longitudinal Dzyaloshinskii-Moriya energy term stemming from the single-ion anisotropy and (ii) the local weakly ferromagnetic response [2]. Furthermore, non-zero curvature κ can drive the helimagnetic phase transition in the spin-flop phase and enables the intermediate canted state for rings with large enough κ. [1] O. Pylypovskyi, D. Kononenko et al., Nano Lett. 20, 8157 (2020); [2] O. Pylypovskyi et al., Appl. Phys. Lett. 118, 182405 (2021); [3] Y. Borysenko et al., Phys. Rev. B, 106, 174426 (2022).

Keywords: antiferromagnetism; curvilinear spin chains

  • Lecture (Conference)
    DPG Meeting of the Condensed Matter Section: Magnetism Division, 26.-31.03.2023, Dresden, Germany

Permalink: https://www.hzdr.de/publications/Publ-36860
Publ.-Id: 36860


Interaction of antiferromagnetic domain walls with crystal defects

Pylypovskyi, O.; Tomilo, A.; Hedrich, N.; Wagner, K.; Shields, B. J.; Kosub, T.; Hübner, R.; Faßbender, J.; Sheka, D. D.; Maletinsky, P.; Makarov, D.

Understanding behavior of magnetic texture in antiferromagnetic nanostructures and thin films is crucial for the design of novel magnetic data storage and logic devices. Here, we derive the boundary conditions for the Néel vector in a two-sublattice antiferromagnet (AFM) and apply them to describe the shape of the domain walls [1,2] and skyrmions [2] in confined samples. In general, the surface of a 3D domain wall behaves as an elastic ribbon which bends in response on the topographic features of the single crystal Cr2 O3 [1]. In presence of the Dzyaloshinskii-Moriya interaction, topologically non-trivial AFM textures possess broadening near the surface. In thin films, the sample’s granularity becomes crucial. We present a model of a granular AFM and, by comparison with Nitrogen Vacancy magnetometry of 200-nm-thick Cr2O3 films, estimate the inter-grain exchange strength. The grain boundaries act as strong pinning sites for the AFM texture. [1] N. Hedrich et al., Nat. Phys. 17, 574 (2021); [2] O. Pylypovskyi et al., Phys. Rev. B 103, 134413 (2021).

Keywords: antiferromagnetism; boundary; granular media

  • Lecture (Conference)
    DPG Meeting of the Condensed Matter Section: Magnetism Division, 26.-31.03.2023, Dresden, Germany

Permalink: https://www.hzdr.de/publications/Publ-36859
Publ.-Id: 36859


Science highlights from the shallow underground laboratory Felsenkeller Dresden

Bemmerer, D.; Schmidt, K.

Underground accelerator laboratories are important instruments to measure nuclear reactions with low cross sections in experimental nu- clear astrophysics. The reduced detector background due the shielding from cosmic rays allows the study of astronuclear reactions at energies relevant to Big Bang nucleosynthesis and stellar burning. The reac- tions 3He(a,g)7Be and 12C(p,g)13N have recently been studied at the shallow underground laboratory Felsenkeller Dresden, where a 5 MV accelerator provides several high intensity ion beams and an ultra-low background counting setup for activation measurements. In the talk, the latest scientific results from the Felsenkeller laboratory, its current capabilities and upcoming enhancements will be summarized.

  • Lecture (Conference)
    Frühjahrstagung Hadronen und Kerne, 20.-24.03.2023, Dresden, Deutschland

Permalink: https://www.hzdr.de/publications/Publ-36858
Publ.-Id: 36858


Improved S-factor of the 12C(p,γ)13N reaction at E =320-620 keV and the 422 keV resonance

Skowronski, J.; Masha, E.; Piatti, D.; Aliotta, M.; Babu, H.; Bemmerer, D.; Boeltzig, A.; Depalo, R.; Caciolli, A.; Cavanna, F.; Csedreki, L.; Fülöp, Z.; Imbriani, G.; Rapagnani, D.; Rümmler, S.; Schmidt, K.; Sidhu, R. S.; Szücs, T.; Turkat, S.; Yadav, A.

The 12C(p,γ)13N reaction is the onset process of both the CNO and Hot CNO cycles that drive massive star, Red and Asymptotic Giant Branch star and novae nucleosynthesis. The 12C(p,γ)13N rate affects the final abundances of the stable 12,13C nuclides, with ramifications for meteoritic carbon isotopic abundances and the s-process neutron source strength. Here, a new underground measurement of the 12C(p,γ)13N cross-section is reported. The present data, obtained at the Felsenkeller shallow-underground laboratory in Dresden (Germany), encompass the 320-620 keV center of mass energy range to include the wide and poorly constrained E = 422 keV resonance that dominates the rate at high temperatures. This work S-factor results, lower than literature by 25%, are included in a new comprehensive R-matrix fit, and the energy of the 1 + first excited state of 13N is found to be 2369.6(4) keV, with radiative and proton width of 0.49(3) eV and 34.9(2) keV respectively. A new reaction rate, based on present R-matrix fit and extrapolation, is suggested.

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36857
Publ.-Id: 36857


Overview of CW electron guns and LCLS-II RF gun performance

Zhou, F.; Adolphsen, C.; Dowell, D.; Xiang, R.

Various continuous-wave (CW) electron gun technologies are reviewed, including DC, superconducting radio frequency RF (SRF), hybrid DC-SRF and normalconducting RF. Also, the SLAC Linac Coherent Light Source II (LCLS-II) normal-conducting RF gun and injector are described, and the performance to date, including the bunch emittance achieved and the dark current observed, is presented.

Keywords: CW; DC gun; SRF gun; NC RF gun; LCLS-II; emittance; dark current

Permalink: https://www.hzdr.de/publications/Publ-36856
Publ.-Id: 36856


Proton-capture rates on carbon isotopes and their impact on the astrophysical 12C/13C ratio

Skowronski, J.; Boeltzig, A.; Ciani, G. F.; Csedreki, L.; Piatti, D.; Aliotta, M.; Ananna, C.; Barile, F.; Bemmerer, D.; Best, A.; Broggini, C.; Bruno, C. G.; Caciolli, A.; Campostrini, M.; Cavanna, F.; Colombetti, P.; Compagnucci, A.; Corvisiero, P.; Davinson, T.; Depalo, R.; Di Leva, A.; Elekes, Z.; Ferraro, F.; Formicola, A.; Fülöp, Z.; Gervino, G.; Gesue, R. M.; Guglielmetti, A.; Gustavino, C.; Gyürky, G.; Imbriani, G.; Junker, M.; Lugaro, M.; Marigo, P.; Masha, E.; Menegazzo, R.; Paticchio, V.; Perrino, R.; Prati, P.; Rapagnani, D.; Rigato, V.; Schiavulli, L.; Sidhu, R. S.; Straniero, O.; Szücs, T.; Zavatarelli, S.

The 12C/13C ratio is a significant indicator of nucleosynthesis and mixing processes during hy- drogen burning in stars. Its value mainly depends on the relative rates of the 12C(p,γ)13N and 13C(p,γ)14N reactions. Both reactions have been studied at the Laboratory for Underground Nu- clear Astrophysics (LUNA) in Italy down to the lowest energies to date (Ec. m. = 60 keV) reaching for the first time the high energy tail of hydrogen burning in the shell of giant stars. Our cross sections, obtained with both prompt γ-ray detection and activation measurements, are the most precise to date with overall systematic uncertainties of 7–8%. Compared with most of the liter- ature, our results are systematically lower, by 25 % for the 12C(p, γ)13N reaction and by 30 % for 13C(p, γ)14N. We provide the most precise value up to now of 3.6 ± 0.4 in the 20 – 120 MK range for the lowest possible 12C/13C ratio that can be produced during H burning in giant stars.

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36855
Publ.-Id: 36855


Nuclear astrophysics underground

Bemmerer, D.

The Felsenkeller underground laboratory for nuclear astrophysics includes a 5 MV Pelletron ion accelerator and Germany’s lowest background high-purity germanium detector setup for radioactivity measurements. The lab is jointly operated by HZDR and TU Dresden. Protected by its 45 m thick rock overburden, the Felsenkeller cosmic-ray muon flux is 40 times lower than at surface. The natural neutron background is 180 times lower, and the background in a gamma-ray detector with muon veto more than 1000 times lower than at surface. These characteristics place the laboratory in a league with deep underground accelerator labs worldwide and enable highly sensitive nuclear reaction experiments.

The scientific program specifically addresses solar fusion, cosmology, and nucleosynthesis in neutron star precursors. The talk will new reaction data addressing deuterium and lithium from the Big Bang, and solar hydrogen burning.These science cases are highly topical and closely linked to efforts at GSI and FAIR.

In addition to in-house research by HZDR and TU Dresden, the lab is open as a facility for scientific users worldwide, with beam time applications reviewed by an independent science advisory board based on the scientific merits. In addition, EU-supported transnational access is available via the ChETEC-INFRA network of small and medium-scale European research infrastructures for nuclear astrophysics.

  • Invited lecture (Conferences)
    GSI Kolloquium, 18.04.2023, Darmstadt, Deutschland

Permalink: https://www.hzdr.de/publications/Publ-36854
Publ.-Id: 36854


Data for "Techno-economic assessment of PEM electrolysis for O2 supply in activated sludge systems – a simulation study based on the BSM2 wastewater treatment plant"

Parra Ramirez, M. A.; Fogel, S.; Reinecke, S.; Hampel, U.

Input files and simulation results for the related publication.

Keywords: Wastewater treatment; Activated sludge; PEM electrolysis; Techno-economic assessment

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36853
Publ.-Id: 36853


A filtering approach for applying the two-fluid model to gas-liquid flows on high resolution grids

Krull, B.; Meller, R.; Tekavcic, M.; Schlegel, F.

The two-fluid model is usually combined with closure forces designed for applications on coarse grids, i.e. bubbles (or particles) are typically assumed to be smaller than a grid cell. Practical applications however include situations where the mesh is comparatively fine, e.g. when meshing the wall boundary layer or in cases with growing bubbles. This may lead to non-convergent behaviour in mesh studies or to void fraction oscillations. To tackle this problem, a filtering approach is proposed, based on an additional diffusion term in the continuity equation. This approach increases the robustness of the results in regions of high spatial resolution, significantly reducing mesh-dependency of the simulation results. The implementation is straightforward, without a need to solve any additional system of equations. It is analysed in four different bubbly flow cases with varying characteristics: 2D/3D, wedge, square, and cuboid computational domains, with resolutions up to 32 cells per bubble diameter, laminar and turbulent flows, and several ways of gas injection. The additional computational effort varies, but is moderate. The proposed approach is applicable in multi-field two-fluid models for which a stable Euler-Euler behaviour on fine meshes is required, for example to prepare the transfer to an interface-resolving volume-of-fluid representation in morphology-adaptive approaches.

Keywords: Multi-phase flows; Two-phase flow; Two-fluid model; Euler-Euler; Mesh dependence; Filtering; Diffusion; Finite volume method; Bubbles; OpenFOAM; Morphology-adaptive methods

Permalink: https://www.hzdr.de/publications/Publ-36852
Publ.-Id: 36852


Europium(III) as luminescence probe for radionuclide interactions with plant cells

Moll, H.; Jessat, J.; Stumpf, T.; Sachs, S.

Abstract
The understanding of the interaction of radionuclides (RNs) with plant cells serves as basis to explore their transfer in the environment and their uptake into the food chain. Europium(III) is used as an analog for the hazardous actinides Am(III) and Cm(III). Our study describes the interaction of Eu(III) with tobacco (Nicotiana tabacum) BY-2 cells on the cellular and molecular level. Cellular level experiments included the determination of the cell viability, the cell growth, and the homeostasis of macro- and microelements in the presence of Eu(III) as well as its bioassociation by the plant cells. Whereas molecular level investigations are focused on the Eu(III) speciation in media and cells applying different complementary luminescence spectroscopic techniques (UV-excitation and direct excitation). Different Eu(III) species could be distinguished in the media after separating the cells and on the BY-2 cells. The characteristic sum spectrum of the cell-bound Eu(III) depicts a very strong intensity of the hypersensitive 5D0  7F2 transition. The cellular and molecular level investigations with BY-2 cells will be compared with results obtained with Daucus carota [1] and Brassica napus cells [2]. The spectroscopic results indicated differences in the Eu(III) speciation on BY-2 cells on one side compared with D. carota and B. napus cells on the other side.

References
[1] J. Jessat; et al. A comprehensive study on the interaction of Eu(III) and U(VI) with plant cells (Daucus carota) in suspension. J. Hazard. Mater. 439; 2023; 129520.
[2] J. Jessat; et al. Bioassociation of U(VI) and Eu(III) by plant (Brassica napus) suspension cell cultures – A spectroscopic investigation. Environ. Sci. Technol. 55; 2021; 6718 – 6728.

Keywords: europium; luminescence spectroscopy; plant cells; speciation

  • Contribution to proceedings
    The 11th International Conference on f Elements (ICFE-11), 22.-26.08.2023, Strasbourg, France
  • Lecture (Conference)
    11th International Conference on f Elements (ICFE-11), 22.-26.08.2023, Strasbourg, France

Permalink: https://www.hzdr.de/publications/Publ-36851
Publ.-Id: 36851


Innovationstreiber KI - KI-Vernetzungsveranstaltung Helmholtz-Zentrum Dresden-Rossendorf 25. November 2022 - Bericht zur Veranstaltung

Juckeland, G.; Steinbach, P.; Giebel, M.; Kiele, S.; Konrad, U.

Eines der wichtigsten Anliegen der KI-Strategie ist es den Wissens- und Technologietransfer zu fördern. Unser Ziel ist es dabei, den Transfer von Forschungsergebnissen in die Wirtschaft und in die Gesellschaft weiter zu verbessern. Dafür möchten wir uns gerne mit Ihnen im Rahmen der Veranstaltung austauschen und über Lösungsansätze diskutieren. Nach einem Grußwort des Vorstands des Helmholtz-Zentrum Dresden-Rossendorf, Herrn Prof. Dr. Sebastian M. Schmidt, und Herrn Staatsminister Sebastian Gemkow haben wir für Sie verschiedene Impulsvorträge von Seiten der Wissenschaft, Wirtschaft und Verwaltung vorbereitet. Insbesondere die Helmholtz-Gemeinschaft als Gastgeberin wird sich mit ihren Aktivitäten vorstellen. Im Rahmen von Themenräumen haben Sie dann die Möglichkeit, sich intensiv in Kleingruppen über die verschiedenen Aspekte und Themen der Nutzung von KI auszutauschen. Am Ende der Veranstaltung soll dann ein Ergebnispapier mit den wesentlichen Erkenntnissen stehen. Die zentralen Fragestellungen sind dabei, wie aus den wissenschaftlichen Erkenntnissen konkrete Anwendungen bzw. Produkte entstehen können und wie man als Unternehmen die Erkenntnisse nutzbar machen kann. In den Themenräumen sollen sich die Teilnehmer dann zu den verschiedenen Fragestellungen des Wissenstransfers, der Kooperation und Umsetzung austauschen. Denn trotz unterschiedlicher Geschäftsfelder und Branchen gibt es bei den grundlegenden Methoden und Herangehensweisen Überschneidungen.

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36850
Publ.-Id: 36850


HZDR Data Policy

Konrad, U.; Reschke, E.; Schramm, B.; Grzeganek, M.; Wolf, B.; Drechsel, T.

The proper management of research data is imperative to ensure that scientific findings are findable, accessible, interoperable and reusable (FAIR). The national and international research organizations support the long-term safeguarding of and the open access to research data from publicly funded research, as laid down in the "Berlin Declaration on Open Access” of 2003 and the “Guidelines on Data Management in Horizon 2020”. The Alliance of German Science Organizations, the Deutsche Forschungsgemeinschaft and the Helmholtz Association took up this idea in their guide- lines for the handling of research data. The HZDR approves the principle of open access to research data. The HZDR supports its guests in the fulfillment of the requirements of funders and of the scientific community. To this end, it pro- vides the necessary infrastructure for data management and regulates the access to research data by these terms and conditions. Open access to research data should be ensured wherever possible taking the pathway of the citable data publication.

Keywords: Data policy; ROBIS; RODARE; Publication Management; Research Data; Research Software; FAIR; OPEN Access; Data provenance

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36849
Publ.-Id: 36849


Data, code, and metadata for: Environmental drivers of body size in North American bats

Alston, J.; Keinath, D.; Willis, C.; Lausen, C.; O'Keefe, J.; Tyburec, J.; Broders, H.; Moosman, P.; Carter, T.; Chambers, C.; Gillam, E.; Geluso, K.; Weller, T.; Burles, D.; Fletcher, Q.; Norquay, K.; Goheen, J.

Data, code, and metadata that can be used to reproduce the analyses underlying 'Environmental drivers of body size in North American bats' by Alston et al. 2023 Functional Ecology (Preprint: https://doi.org/10.1101/2021.07.28.454183).

Individual data owners are detailed in the data. Data may only be used to reproduce the analyses underlying Alston et al. (2023). Any other use requires the written permission of the individual data owners.

For more detailed information, please visit the metadata file.

Related publications

Permalink: https://www.hzdr.de/publications/Publ-36848
Publ.-Id: 36848


Environmental drivers of body size in North American bats

Alston, J.; Keinath, D.; Willis, C.; Lausen, C.; O'Keefe, J.; Tyburec, J.; Broders, H.; Moosman, P.; Carter, T.; Chambers, C.; Gillam, E.; Geluso, K.; Weller, T.; Burles, D.; Fletcher, Q.; Norquay, K.; Goheen, J.

1. Bergmann's rule—which posits that larger animals live in colder areas—is thought to influence variation in body size within species across space and time, but evidence for this claim is mixed.

2. We used Bayesian hierarchical models to test four competing hypotheses for spatiotemporal variation in body size within 20 bat species across North America: (1) the heat conservation hypothesis, which posits that increased body size facilitates body heat conservation (and which is the traditional explanation for the mechanism underlying Bergmann's rule); (2) the heat mortality hypothesis, which posits that increased body size increases susceptibility to acute heat stress; (3) the resource availability hypothesis, which posits that increased body size is enabled in areas with more abundant food; and (4) the starvation resistance hypothesis, which posits that increased body size reduces susceptibility to starvation during acute food shortages.

3. Spatial variation in body mass was most consistently (and negatively) correlated with mean annual temperature, supporting the heat conservation hypothesis. Across time, variation in body mass was most consistently (and positively) correlated with net primary productivity, supporting the resource availability hypothesis.

4. Climate change could influence body size in animals through both changes in mean annual temperature and resource availability. Rapid reductions in body size associated with increasing temperatures have occurred in short-lived, fecund species, but such reductions will be obscured by changes in resource availability in longer-lived, less fecund species.

Keywords: Bayesian hierarchical modeling; Bergmann's Rule; body size clines; Chiroptera; climate change; geographic information systems; primary productivity

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36847
Publ.-Id: 36847


LDOS/SNAP data for MALA: Beryllium at high temperatures

Fiedler, L.; Cangi, A.

# Authors:

- Fiedler, Lenz (HZDR / CASUS)
- Cangi, Attila (HZDR / CASUS)

# Affiliations:

HZDR - Helmholtz-Zentrum Dresden-Rossendorf
CASUS - Center for Advanced Systems Understanding

# Dataset description

- System: Be256
- Temperature(s): 3750K, 7500K, 10000K
- Mass density(ies): 1.915 gcc
- Crystal Structure: bcc (material mp-20 in the materials project)
- Number of atomic snapshots: 50
   - 30 (3750K)
   - 10 (7500K)
   - 10 (10000)
- Contents:
   - ideal crystal structure: no
   - MD trajectory: no
   - Atomic positions: no
   - DFT inputs: no
   - DFT outputs (energies): yes
   - SNAP vectors: no
   - LDOS vectors: yes (partially, see below)
        - dimensions: 160x80x80x250
      - note: LDOS parameters are the same for all sizes of the unit cell
   - trained networks: no

# Data generation

Ideal crystal structures were obtained using the Materials Project. (https://materialsproject.org/materials/mp-87/)
DFT-MD calculations were performed using the Vienna Ab initio Simulation Package (https://www.vasp.at/, VASP). DFT calculations were performed using QuantumESPRESSO.
For the VASP calculations, the standard VASP pseudopotentials were used. For Quantum Espresso, pslibrary was used (https://dalcorso.github.io/pslibrary/).
The LDOS was preprocessed using MALA.

# Dataset structure

Each temperature folder contains the following folders:

- ldos: holds the LDOS vectors (LDOS was not calculated for all snapshots!)
- dft_outputs: holds the outputs from the DFT calculations, i.e. energies in the form of a QE output file

Please note that the numbering of the snapshots is contiguous per temperature/mass density/number of atoms, and only data used in publications has been uploaded at this point

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36846
Publ.-Id: 36846


Scripts and models for "Machine learning the electronic structure of matter across temperatures"

Fiedler, L.; Modine, N. A.; Miller, K. D.; Cangi, A.

# Data and Scripts for "Machine learning the electronic structure of matter across temperatures"

This dataset contains data and calculation scripts for the publication "Machine learning the electronic structure of matter across temperatures".
Its goal is to enable interested parties to reproduce the experiments we have carried out.

## Prerequesites

The following software versions are needed for the python scripts:

- `python`: 3.8.x
- `mala`: 1.2.0 
- `numpy`: 1.23.0 (lower version may work)

Further, make sure you have downloaded additional data such as local pseudopotentials and training data.

## Contents

- `data_analysis/`: Contains scripts contain useful functions to reproduce the analysis carried out on the provided 
                    data.
- `model_training/`: Contains scripts that allow the training and testing of the models discussed in the accompanying
                     publication.
- `trained_models`: Contains the models discussed in the accompanying publication. Per data set, five models with 
                    different random initializations were trained. 

Related publications

Downloads

Permalink: https://www.hzdr.de/publications/Publ-36845
Publ.-Id: 36845


Weight Calculation with the help of a recursive Monte-Carlo method

Yadav, P.; Konheiser, J.; Baier, S.; Rachamin, R.

muss noch eingetragen werden.

Keywords: Recursive Monte-Carlo; Weight calculation; MCNP6

  • Lecture (Conference)
    AAA Workshop, 10.05.2023, Garching, Germany

Permalink: https://www.hzdr.de/publications/Publ-36844
Publ.-Id: 36844


Application of neutron fluence monitors for source term validation in F-18 production with a medical cyclotron

Konheiser, J.; Müller, S.

Imaging techniques such as positron emission tomography need radionuclides that can be produced with cyclotrons. The involved nuclear reactions mostly produce neutron and gamma radiation, which must be shielded. In order to be able to determine the required thickness of the shielding for a new medical cyclotron, corresponding radiation protection calculations were carried out. The necessary neutron source term was supplied by the manufacturer. To verify this source term, additional source terms were calculated with the MCNP6 and the FLUKA code packages. The results with the source, on base of code internal nuclear models, produced comparable results, but the neutron yield with the source supplied by the manufacturer is lower by a factor of about 5. To validate the results, experiments were carried out on an already existing cyclotron. Neutron fluence was measured with standard monitors which are used in reactor dosimetry. The experiment was performed during regular 18F production. The activities of the nuclides were measured by gamma spectroscopy and compared with the calculated activities. We found varied agreements between calculated results with the internal source and experimental results.

Keywords: neutron source; Monte Carlo; MCNP6; FLUKA; 18F production; Neutron fluence monitors

  • Poster
    17th International Symposium on Reactor Dosimetry, 21.-26.05.2023, Lausanne, Switzerland

Permalink: https://www.hzdr.de/publications/Publ-36843
Publ.-Id: 36843


Pages: [1.] [2.] [3.] [4.] [5.] [6.] [7.] [8.] [9.] [10.] [11.] [12.] [13.] [14.] [15.] [16.] [17.] [18.] [19.] [20.] [21.] [22.] [23.] [24.] [25.] [26.] [27.] [28.] [29.] [30.] [31.] [32.] [33.] [34.] [35.] [36.] [37.] [38.] [39.] [40.] [41.] [42.] [43.] [44.] [45.] [46.] [47.] [48.] [49.] [50.] [51.] [52.] [53.] [54.] [55.] [56.] [57.] [58.] [59.] [60.] [61.] [62.] [63.] [64.] [65.] [66.] [67.] [68.] [69.] [70.] [71.] [72.] [73.] [74.] [75.] [76.] [77.] [78.] [79.] [80.] [81.] [82.] [83.] [84.] [85.] [86.] [87.] [88.] [89.] [90.] [91.] [92.] [93.] [94.] [95.] [96.] [97.] [98.] [99.] [100.] [101.] [102.] [103.] [104.] [105.] [106.] [107.] [108.] [109.] [110.] [111.] [112.] [113.] [114.] [115.] [116.] [117.] [118.] [119.] [120.] [121.] [122.] [123.] [124.] [125.] [126.] [127.] [128.] [129.] [130.] [131.] [132.] [133.] [134.] [135.] [136.] [137.] [138.] [139.] [140.] [141.] [142.] [143.] [144.] [145.] [146.] [147.] [148.] [149.] [150.] [151.] [152.] [153.] [154.] [155.] [156.] [157.] [158.] [159.] [160.] [161.] [162.] [163.] [164.] [165.] [166.] [167.] [168.] [169.] [170.] [171.] [172.] [173.] [174.] [175.] [176.] [177.] [178.] [179.] [180.] [181.] [182.] [183.] [184.] [185.] [186.] [187.] [188.] [189.] [190.] [191.] [192.] [193.] [194.] [195.] [196.] [197.] [198.] [199.] [200.] [201.] [202.] [203.] [204.] [205.] [206.] [207.] [208.] [209.] [210.] [211.] [212.] [213.] [214.] [215.] [216.] [217.] [218.] [219.] [220.] [221.] [222.] [223.] [224.] [225.] [226.] [227.] [228.] [229.] [230.] [231.] [232.] [233.] [234.] [235.] [236.] [237.] [238.] [239.] [240.] [241.] [242.] [243.] [244.] [245.] [246.] [247.] [248.] [249.] [250.] [251.] [252.] [253.] [254.] [255.] [256.] [257.] [258.] [259.] [260.] [261.] [262.] [263.] [264.] [265.] [266.] [267.] [268.] [269.] [270.] [271.] [272.] [273.] [274.] [275.] [276.] [277.] [278.] [279.] [280.] [281.] [282.] [283.] [284.] [285.] [286.] [287.] [288.] [289.] [290.] [291.] [292.] [293.] [294.] [295.] [296.] [297.] [298.] [299.] [300.] [301.] [302.] [303.] [304.] [305.] [306.] [307.] [308.] [309.] [310.] [311.] [312.] [313.] [314.] [315.] [316.] [317.] [318.] [319.] [320.] [321.] [322.] [323.] [324.] [325.] [326.] [327.] [328.] [329.] [330.] [331.] [332.] [333.] [334.] [335.] [336.] [337.] [338.] [339.] [340.] [341.] [342.] [343.] [344.] [345.] [346.] [347.] [348.] [349.]